Lesson 4 of 10 · 15 min

Resistance and Ohm's law

Describe resistance and what causes it, use V=IRV = IR with SI prefixes, and calculate the power dissipated in a resistor with P=VIP = VI and P=I2RP = I^2R.

What you will be able to do

  • Describe resistance and explain what causes it in a metal conductor.
  • Solve problems with V=IRV = IR, including values with SI prefixes.
  • Describe power dissipation in a resistor and calculate it with P=VIP = VI, P=I2RP = I^2R or P=V2RP = \dfrac{V^2}{R}.

Connect a car's 12 V battery to a headlight and about 4.6 A flows. Connect the same battery to the dashboard clock and only a few milliamperes flow. The battery is the same; what differs is how hard it is to drive charge through each device. That property is resistance.

In a metal, free electrons drift through a lattice of positive ions that vibrate about fixed positions. As the electrons drift they keep colliding with the ions and transferring energy to them. The ions vibrate more, so the metal heats up. These collisions oppose the flow of charge, and that opposition is resistance.

Resistance is larger for a longer wire (more collisions along the way) and smaller for a thicker one (more paths side by side). It depends on the material, and for a metal it increases as the metal gets hotter, because hotter ions vibrate more.

Definition

Resistance

The resistance RR of a component is the potential difference across it divided by the current through it:

R=VIorV=IRR = \frac{V}{I} \qquad\text{or}\qquad V = IR

Resistance is measured in ohms (Ω\Omega), where 1 Ω=1 V A−11\unit{\Omega} = 1\unit{V\,A^{-1}}. A 1 Ω resistor needs a potential difference of 1 V across it to drive a current of 1 A through it.

From the formula and data book
V=IRV = IR
Interactive

Ohm's law in action

Double the battery's potential difference and watch the current. Then put it back and double the resistance instead. For a fixed resistor, the current is directly proportional to the potential difference.

History

Georg Ohm

Georg Ohm, a German schoolteacher, published his law in 1827 after measuring currents in wires of different lengths and thicknesses. Many scientists of the day dismissed it, and it took more than a decade for his work to be widely accepted. The unit of resistance is named after him.

Worked example

Ohm's law with prefixes

  • Simple familiar
  • Technology active

A 2.2 kΩ resistor has a potential difference of 9.0 V across it. Calculate the current through it, in milliamperes.

4 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Convert prefixed units to SI before substituting.

  2. Rearrange V=IRV = IR for the unknown.

  3. Convert back to the unit asked for.

Watch out for

  • Dividing 9.0 by 2.2 gives 4.1, but in amperes, a thousand times too big. It only looks right because the prefixes happen to cancel: kΩ on the bottom gives mA.

A 6.0 V battery is connected across a 30 Ω resistor. What current flows through the resistor?

in A

Give 2 significant figures.

A component has a potential difference of 4.5 V across it and a current of 15 mA through it. What is its resistance?

in Omega

Give 2 significant figures.

As charges move through a resistor they transfer electrical energy to the lattice. It becomes thermal energy and spreads, or dissipates, into the surroundings. That's the whole point of a toaster or a heater, and it's wasted energy in a phone charger or a power line.

The rate is still P=VIP = VI. Substituting V=IRV = IR gives a form that needs only the current and the resistance:

Power dissipated in a resistor, from the formula and data book
P=I2RP = I^2R
Where P=I2RP = I^2R and P=V2RP = \frac{V^2}{R} come from

Start from P=VIP = VI.

  • Replace VV with IRIR:   P=(IR) I=I2R\;P = (IR)\,I = I^2R.
  • Replace II with VR\dfrac{V}{R}:   P=V(VR)=V2R\;P = V\left(\dfrac{V}{R}\right) = \dfrac{V^2}{R}.

All three give the same power for the same resistor, so choose the one that uses the quantities you know. P=V2RP = \dfrac{V^2}{R} isn't on the formula sheet, so show the substitution when you use it.

Worked example

Will the resistor overheat?

  • Complex familiar
  • Technology active

A 47 Ω resistor rated at 0.25 W carries a current of 0.20 A. (a) Calculate the power dissipated in it. (b) Is the resistor safe to use? (c) What is the largest current it can safely carry?

4 steps

Try it yourself first, then check the working one step at a time.

Method

  1. P=I2RP = I^2R when you know the current and resistance.

  2. Compare the power with the rating.

  3. Rearrange the same formula to find the limit.

Watch out for

  • Forgetting to square the current gives 0.20×47=9.40.20 \times 47 = 9.4, which is the potential difference in volts, not a power.

A current of 2.5 A flows through a 4.0 Ω heating element. At what rate does the element dissipate energy?

in W

Give 2 significant figures.

Common mistake

The right V and the right I

Use the potential difference across that resistor and the current through that resistor. When a resistor shares a circuit with other components, the battery's potential difference is not the one across it.

Strictly, Ohm's law says the current through a conductor at constant temperature is directly proportional to the potential difference across it. V=IRV = IR defines resistance for any component, ohmic or not, as you'll see in the next lesson.

Exam tip

Show the substitution

Write the formula, then the substitution with units, for example I=VR=9.0 V2200 ΩI = \dfrac{V}{R} = \dfrac{9.0\unit{V}}{2200\unit{\Omega}}, then the answer with a unit and two or three significant figures. Convert prefixes before you substitute.

Summary

  • Resistance comes from charge carriers colliding with the vibrating ions of the conductor, which transfers electrical energy to thermal energy.

  • R=VIR = \dfrac{V}{I}, measured in ohms, and V=IRV = IR links potential difference, current and resistance.

  • Convert prefixes first: 1 kΩ=103 Ω1\unit{k\Omega} = 10^{3}\unit{\Omega} and 1 mA=10−3 A1\unit{mA} = 10^{-3}\unit{A}.

  • The power dissipated in a resistor is P=VI=I2R=V2RP = VI = I^2R = \dfrac{V^2}{R}.

  • A resistor's power rating is the greatest power it can dissipate without overheating.

Finished the lesson?

Try the 3 quick checks above and the lesson completes itself, or mark it complete now.

Lesson 4 of 100% read

Save your progress with a free account