Lesson 10 of 10 · 17 min
Circuits for real-life purposes
Apply circuit ideas to household wiring, overloaded circuits, LED circuits and sensors, and choose components so a circuit does a particular job.
What you will be able to do
- Explain why household appliances are connected in parallel, with a circuit breaker in series.
- Calculate the total current on a household circuit and judge whether it will trip.
- Design a simple circuit for a purpose, such as setting the current through an LED.
- Describe how a sensor in a series circuit can switch a device on and off.
On a scorching summer evening a family runs the air conditioner, cooks dinner, boils the kettle and charges every phone in the house. Whether the power stays on depends on the rules from this topic: how currents add in parallel, and how much current the wiring can safely carry.
Household appliances are connected in parallel across the supply. The circuit breaker is in series with all of them, so it carries their total current.
Household appliances are connected in parallel across the supply, for three reasons:
- every appliance gets the full 230 V it was designed for
- each one can be switched on and off without affecting the others
- if one fails, the rest keep working.
The price is that the currents add. The supply wires and the circuit breaker, which is in series with the whole circuit, carry the total current of every appliance that's switched on. If that total exceeds the breaker's rating, it trips and opens the circuit before the wiring overheats. The heating matters because the power dissipated in the wires, , grows with the square of the current.
Worked example
Is the power board overloaded?
On a 40 °C day, a student runs a 1.5 kW portable air conditioner, a 0.40 kW gaming computer and a 0.15 kW television from one power board plugged into a 230 V socket. The power board is rated at 10 A.
(a) Calculate the current in the power board's lead. (b) The student wants to add a 0.90 kW portable air conditioner for a second room. Would the board be overloaded? (c) What is the most extra power the board could safely supply?
Step 1: Add the powers
The appliances are in parallel, so their currents add, and so do their powers.
Step 2: Find the current in the lead
All the branch currents combine in the board's lead, by Kirchhoff's current law.
Step 3: Add the second air conditioner
, so .
Step 4: Compare with the rating
12.8 A is more than 10 A, so the board would be overloaded. Its wiring would overheat, since the power dissipated in the lead grows as .
Step 5: Find the spare capacity
Maximum power: . Spare: .
Try it yourself first, then check the working one step at a time.
Answer
(a) 8.9 A. (b) Yes: the current would be about 13 A, above the 10 A rating. (c) About 250 W more.
Method
Parallel appliances: add the powers (or the currents).
Total current from .
Compare with the rating; spare power is the rated power minus the power in use.
Watch out for
Working with kilowatts in gives a current a thousand times too small.
Thinking the new device only shares the existing current. Each parallel branch adds its own current.
A 2.4 kW heater, a 1.2 kW microwave oven and a 0.20 kW television run at the same time on one 230 V power circuit. What is the total current in the circuit's supply wires?
Note
Extreme weather and a stable supply
In a heatwave, or a European cold snap when millions of electric heaters switch on, demand climbs at the same time across a whole region. The network must generate and deliver that peak power; if it can't, operators may cut supply to some areas to protect the system. Hospitals, phones, computers and the internet all rely on a stable supply, so efficient appliances, good insulation and shifting demand to other times (such as charging an electric car overnight) all help.
International standards set the ratings of cables, breakers and appliances, so that devices designed in one country work safely with the wiring of another.
Designing a circuit means choosing components so it does a job. An LED is a good example. It needs a particular current, typically about 20 mA, and at that current the potential difference across a red LED is about 2 V. Connect it straight across a 9 V battery and the current would be far too large and destroy it.
The fix is a resistor in series with the LED. The resistor carries the same current and takes the rest of the supply potential difference:
A series resistor sets the current through the LED.
Worked example
Choosing a resistor for an LED
A red LED needs a current of 20 mA, at which the potential difference across it is 2.0 V. Design a circuit to run it from a 9.0 V battery, choosing a series resistor from the standard values 220 Ω, 330 Ω, 390 Ω and 470 Ω. Find the power dissipated in the resistor, and comment on the design.
Step 1: Find the potential difference across the resistor
The LED and resistor are in series, so by Kirchhoff's voltage law their potential differences add to the supply.
Step 2: Find the ideal resistance
Step 3: Choose a standard value
330 Ω would allow , more than the LED should carry. Choose the next value up, 390 Ω.
Rounding up keeps the current at or below the LED's rating.
Step 4: Find the actual current
, assuming the LED's potential difference stays near 2.0 V.
Step 5: Find the power in the resistor
, comfortably below the 0.25 W rating of a standard resistor.
Step 6: Comment on efficiency
The LED itself uses only . About of the battery's energy becomes heat in the resistor, so a lower-voltage supply, such as two AA cells (3.0 V), would waste far less.
Try it yourself first, then check the working one step at a time.
Answer
Use a 390 Ω resistor in series with the LED. The current is about 18 mA and the resistor dissipates about 0.13 W, so a standard 0.25 W resistor is fine. The design wastes about 78% of the battery's energy as heat, so a lower supply potential difference would be more efficient.
Method
The series resistor takes the supply minus the LED's potential difference.
, then round up to a standard value.
Check the resistor's power against its rating.
Watch out for
Using the whole 9.0 V: ignores the LED's share.
Rounding down to 330 Ω, which lets more than the rated current flow.
An LED needs a current of 15 mA, at which the potential difference across it is 2.0 V. What resistance should be connected in series with it so that it runs correctly from a 5.0 V supply?
Series circuits can also sense. A thermistor is a non-ohmic resistor whose resistance falls as it warms up. Connect it in series with a fixed resistor across a battery and the two share the supply potential difference in proportion to their resistances. As the room heats up, the thermistor's resistance falls, so its share falls and the fixed resistor's share rises. That rising potential difference can switch on a fan. Swap in a light-dependent resistor, whose resistance falls in bright light, and the same idea turns a street light off at dawn and on at dusk.
A thermistor, whose resistance falls as its temperature rises, is connected in series with a fixed 10 kΩ resistor across a 6.0 V battery. As the temperature rises, what happens to the potential difference across the fixed resistor?
History
Hertha Ayrton and Florence Violet McKenzie
Hertha Ayrton studied the electric arc, the brilliant light source of the arc lamps that lit streets in the late 1800s. Her experiments explained what makes an electric arc hiss. In 1899 she became the first woman elected a member of the Institution of Electrical Engineers, and in 1906 the Royal Society awarded her its Hughes Medal.
Florence Violet McKenzie became Australia's first female electrical engineer when she completed her diploma at Sydney Technical College in 1923. In 1934 she founded the Electrical Association for Women to teach people to use electricity safely and well at home, and during World War II she trained thousands of signallers in Morse code.
Beyond the syllabus. A real battery has a small internal resistance, so some of its potential difference is used up inside it, and the bigger the current, the less is left at its terminals. Lower the load resistance and watch the terminal potential difference fall: it is why a car's headlights dim while the starter motor turns.
Summary
Household appliances are connected in parallel so each gets the full supply potential difference and can be switched on its own. Their currents add.
A circuit breaker in series with the circuit trips when the total current exceeds its rating, protecting the wiring from overheating.
The total current on a circuit is the total power divided by the supply potential difference, .
A series resistor sets the current through an LED by taking the rest of the supply: .
A thermistor or light-dependent resistor in series with a fixed resistor turns a change in temperature or light into a change in potential difference.
Finished the lesson?
Try the 3 quick checks above and the lesson completes itself, or mark it complete now.