Physics · Unit 1 · Topic 3

Electrical circuits

Charge, current, potential difference, resistance and power; ohmic and non-ohmic devices; resistance from V–I graphs with uncertainty; and series, parallel and combination circuits solved with the conservation of charge and energy.

  • 10 lessons
  • 2 h 40 min of lessons
  • 16 worked examples
  • 15 hours in the syllabus
0 of 10

Start here

Electric charge and current

Lesson 1 of 10 · 15 min

Start the topic

Lessons

10
  1. Electric charge and current (up next)

    Describe electric charge and the carriers that move it, explain conventional current, and use I=qtI = \dfrac{q}{t} to link current, charge and time.

  2. Potential difference: energy per coulomb

    Explain potential difference as the energy each coulomb of charge gains or transfers, explain why separating charge creates it, and use V=WqV = \dfrac{W}{q}.

  3. Electrical power and energy

    Use P=WtP = \dfrac{W}{t} and P=VIP = VI to find the power of devices, work out energy in joules and kilowatt hours, and compare the running cost and efficiency of household devices.

  4. Resistance and Ohm's law

    Describe resistance and what causes it, use V=IRV = IR with SI prefixes, and calculate the power dissipated in a resistor with P=VIP = VI and P=I2RP = I^2R.

  5. Ohmic and non-ohmic conductors

    Compare the I–V characteristics of ohmic resistors with non-ohmic devices such as filament lamps and diodes, and find the resistance of a non-ohmic device at a point.

  6. Finding resistance from a V–I graph

    Analyse data from the resistance practical, find resistance from the gradient of a V–I graph, and estimate its uncertainty from the steepest and shallowest lines.

  7. Series circuits

    Describe series connections and solve series circuits using one current, potential differences that add, and resistances that add.

  8. Parallel circuits

    Describe parallel connections and solve parallel circuits using one potential difference, currents that add at junctions, and an equivalent resistance smaller than any branch.

  9. Combination circuits and Kirchhoff's laws

    Reduce series–parallel circuits to one equivalent resistance, work back to every current and potential difference, and solve or check circuits with Kirchhoff's laws.

  10. Circuits for real-life purposes

    Apply circuit ideas to household wiring, overloaded circuits, LED circuits and sensors, and choose components so a circuit does a particular job.

  11. Topic quiz

    Ten questions across the topic, from foundation to complex unfamiliar. Your results feed your mastery.

About this topic

Every device you plug in or charge runs on the same few ideas. Charge flows as a current. Each coulomb of charge carries energy, and potential difference measures how much. Resistance decides how much current a given potential difference can drive, and power tells you how fast energy is transferred.

In this topic you build those ideas from the particles up, then use them to analyse series, parallel and combination circuits, find resistance from experimental data with its uncertainty, and design simple circuits for real purposes, from an LED torch to a household power circuit on a 40 °C day.

Two conservation laws hold it all together. Charge is never used up, so the current into any junction equals the current out. Energy is conserved, so the energy each coulomb gains in the battery equals the energy it gives up in the loads. Gustav Kirchhoff turned these into the two laws that solve every circuit in this course.

Before you start

Builds on Heating processes.

  • Rearranging a formula such as V=IRV = IR to make any quantity the subject.
  • Scientific notation and the SI prefixes milli (m), micro (μ\mu), kilo (k) and mega (M).
  • Atoms contain positive protons and negative electrons, and energy is conserved (Year 9–10 science).
  • Efficiency, η=energy outputenergy input×100%\eta = \dfrac{\text{energy output}}{\text{energy input}} \times 100\%, from Heating processes.
  • The gradient of a straight-line graph as rise over run.

What QCAA says you need to know31 dot points

Current, potential difference and energy flow

Circuit analysis and design

Science as a human endeavour (SHE)

Science inquiry

Subject matter from the Physics General senior syllabus 2025 v1.3 (opens in a new tab), CC BY 4.0 © State of Queensland (QCAA).

The focus areas you can practise on their own. Each one maps to dot points above.

  • Charge and current

    Describe charge and charge carriers, explain conventional current, and use $I = \frac{q}{t}$ and $N = \frac{q}{e}$.

    Practise
  • Potential difference and energy

    Explain potential difference as energy per coulomb, why charge separation creates it, and use $V = \frac{W}{q}$.

    Practise
  • Power and electrical energy

    Use $P = \frac{W}{t}$ and $P = VI$, work in joules and kilowatt hours, and compare running costs and efficiency.

    Practise
  • Resistance and Ohm's law

    Describe resistance, use $V = IR$ with SI prefixes, and find the power dissipated in a resistor.

    Practise
  • Ohmic and non-ohmic conductors

    Interpret I–V characteristics and find the resistance of a non-ohmic device at a point.

    Practise
  • Resistance from V–I graphs

    Find resistance from the gradient of a V–I graph, with its uncertainty, percentage uncertainty and percentage error.

    Practise
  • Circuit diagrams and meters

    Draw and read circuit diagrams, place ammeters and voltmeters correctly, and identify series and parallel parts.

    Practise
  • Series circuits

    Use one current, $V_t = V_1 + V_2 + \cdots$ and $R_t = R_1 + R_2 + \cdots$ to solve series circuits.

    Practise
  • Parallel circuits

    Use one potential difference, $I_t = I_1 + I_2 + \cdots$ and the reciprocal rule to solve parallel circuits.

    Practise
  • Series–parallel circuits

    Reduce a combination circuit to its equivalent resistance, then find every current and potential difference.

    Practise
  • Kirchhoff's laws

    Apply conservation of charge at junctions and conservation of energy around loops to find unknown currents and potential differences.

    Practise
  • Circuits for real-life purposes

    Apply circuit ideas to household wiring, overloads, LEDs, lighting efficiency and charging, and choose components for a purpose.

    Practise

Worked examples16

All 16

Common mistakes

Thinking current is used up

The current leaving a lamp equals the current entering it. Charge is conserved; what the lamp takes from each coulomb is energy, not charge.

Potential difference "through" a component

Current flows through a component; potential difference is across it, between two points. A voltmeter connects across the component, in parallel.

Forgetting SI units

Convert mA to A, kΩ to Ω, minutes to seconds and kW to W before you substitute. 2.0 min2.0\unit{min} is 120 s120\unit{s}, and 4.7 kΩ4.7\unit{k\Omega} is 4700 Ω4700\unit{\Omega}.

Not inverting in the parallel rule

1Rt=16.0+112=0.25 Ω−1\frac{1}{R_t} = \frac{1}{6.0} + \frac{1}{12} = 0.25\unit{\Omega^{-1}} gives Rt=4.0 ΩR_t = 4.0\unit{\Omega}, not 0.25 Ω0.25\unit{\Omega}. A parallel combination is always smaller than its smallest branch.

Using the supply potential difference for one component

In series and combination circuits the supply potential difference is shared. Use the potential difference across that component and the current through that component.

Reading resistance from the wrong gradient

On a V–I graph (V up, I across) the gradient is RR. On an I–V graph (I up, V across) it is 1R\frac{1}{R}. For a non-ohmic device, R=VIR = \frac{V}{I} at the point, not the gradient of the curve.

Mixing up power and energy

Kilowatts measure power, a rate. Kilowatt hours measure energy, an amount. A bill charges for energy, so multiply power by time first.

Splitting a parallel current equally

Current divides between branches in inverse proportion to their resistance. The smallest resistance carries the largest current.

Connecting an ammeter in parallel

An ammeter has almost no resistance. Connected across a component it creates a short circuit; it belongs in series.

Units and significant figures

Give every answer a unit and the same number of significant figures as the least precise data, usually two or three in this topic.

Exam tips

  1. Write the formula, substitute values with units, then give the answer with a unit and significant figures that match the data. A correct substitution can earn a method mark even if the final answer slips.

  2. Convert to SI units before substituting: mA to A, kΩ to Ω, minutes to seconds. For running costs keep power in kW and time in hours to get kW h.

  3. Label circuit diagrams as you solve them: write each current and potential difference beside its component. Then check with Kirchhoff's laws, since currents at each junction and potential differences round each loop must balance.

  4. When you explain circuit behaviour, name the conservation law and apply it: "charge is conserved, so the current into the junction equals the current out".

  5. Read the axes before you use a gradient. Use two points on the line of best fit that are far apart, not two data points, and show the rise and run.

  6. For the uncertainty in a gradient, use the steepest and shallowest lines that still pass through every error bar; the uncertainty is half the difference of their gradients.

  7. Describe an I–V characteristic precisely: "a straight line through the origin, so current is directly proportional to potential difference and the resistance is constant".

  8. Both external papers allow a QCAA-approved calculator, so the marks are in the physics: the right formula, units, setting out and a reasonableness check.

Where this shows up

  • Household wiring connects appliances in parallel across 230 V, with circuit breakers that open when the total current is too high.

  • Phone and laptop batteries are rated in mA h (charge) and W h (energy); chargers are rated in watts.

  • Electric vehicles charge at a power P=VIP = VI; the time and cost of a charge follow from the energy needed.

  • LED lighting gives the same light for a fraction of the power of incandescent globes, and series resistors set the current through an LED.

  • Electricity demand peaks in heatwaves and cold snaps, when millions of air conditioners and heaters run at once.

  • Thermistors and light-dependent resistors in series circuits switch fans, heaters and street lights automatically.

  • A car's lights and accessories run in parallel from its 12 V battery.

Save your progress with a free account