Lesson 5 of 10 · 15 min

Ohmic and non-ohmic conductors

Compare the I–V characteristics of ohmic resistors with non-ohmic devices such as filament lamps and diodes, and find the resistance of a non-ohmic device at a point.

What you will be able to do

  • Distinguish ohmic and non-ohmic conductors from their I–V characteristics.
  • Calculate the resistance of a non-ohmic device at a point with R=VIR = \dfrac{V}{I}.
  • Explain why the resistance of a filament lamp increases as it heats up.
  • Describe an experiment that compares ohmic and non-ohmic components.

Incandescent globes usually blew the moment they were switched on, rarely halfway through an evening. A cold filament has a much lower resistance than a hot one, so for a split second at switch-on the current is several times its normal value. A component whose resistance changes like this is non-ohmic.

Definition

Ohmic and non-ohmic

In an ohmic conductor the current is directly proportional to the potential difference across it, as long as its temperature stays constant. Its resistance is constant, so its I–V graph is a straight line through the origin. A metal-film resistor at room temperature is ohmic.

In a non-ohmic conductor the resistance changes as the current or potential difference changes, so its I–V graph is not a straight line through the origin. Filament lamps, diodes and thermistors are non-ohmic.

I–V characteristics of a 20 Ω resistor (ohmic) and a filament lamp (non-ohmic).

Read the lamp's curve at two points. At 2.0 V the current is 0.20 A, so R=2.00.20=10 ΩR = \dfrac{2.0}{0.20} = 10\unit{\Omega}. At 6.0 V the current is 0.30 A, so R=6.00.30=20 ΩR = \dfrac{6.0}{0.30} = 20\unit{\Omega}.

Tripling the potential difference only raised the current by half: the lamp's resistance doubled. At 6.0 V the lamp has the same resistance as the 20 Ω resistor, which is why the two graphs meet there.

Interactive

Build an I–V characteristic

Horizontal axis: potential difference VV in volts. Vertical axis: current II in amperes. In this simple model the resistance is R=R0+kVR = R_0 + kV, rising as the device heats. Set k=0k = 0 for an ohmic resistor.

Why does the lamp's resistance rise? A larger potential difference drives a larger current, so energy is transferred to the filament faster and its temperature climbs, to about 2500 °C at full brightness. The hotter metal ions vibrate with larger amplitude, so the drifting electrons collide with them more often. More collisions mean more resistance, so the current grows more slowly than the potential difference and the graph bends over.

Common components and their I–V characteristics
ComponentOhmic?Shape of the I–V graphWhy
Resistor at constant temperatureOhmicStraight line through the originIts resistance stays constant
Filament lampNon-ohmicA curve that flattens as VV increasesThe filament heats up and its resistance rises
Diode (including an LED)Non-ohmicAlmost no current until about 0.7 V forwards (about 2 V for a red LED), and almost none in reverseIt conducts in one direction only
ThermistorNon-ohmicA curve that bends upwards as VV increasesIt warms up and its resistance falls as its temperature rises

Common mistake

Resistance at a point

The resistance at a point on a curve is VI\dfrac{V}{I} at that point. It is not the gradient of the curve there, and not ΔVΔI\dfrac{\Delta V}{\Delta I} between two points. On an I–V graph (current up the side), even the gradient of a straight line is 1R\dfrac{1}{R}, not RR. For a curve, read VV and II off the graph and divide.

Worked example

Resistance of a filament lamp from its I–V graph

  • Complex familiar
  • Technology active

The graph shows the I–V characteristic of a 12 V car lamp. (a) Determine the lamp's resistance at 4.0 V and at 12 V. (b) Explain the difference.

4 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Read V and I at the point from the graph.

  2. Divide V by I at that point.

  3. Explain changes in resistance with temperature and collisions.

Watch out for

  • Using ΔVΔI=12−4.00.30−0.20=80 Ω\frac{\Delta V}{\Delta I} = \frac{12 - 4.0}{0.30 - 0.20} = 80\unit{\Omega}, which is not the resistance at either point.

  • Using the gradient of the curve, which on an I–V graph isn't the resistance at all.

A silicon diode carries a current of 20 mA when the potential difference across it is 0.75 V. What is its resistance at this point?

in Omega

Give 2 significant figures.

When the potential difference across a filament lamp rises from 2.0 V to 6.0 V, the current through it rises from 0.20 A to 0.30 A. Which statement is correct?

Choose one answer

You can compare components experimentally. Connect the component in series with an ammeter and a variable supply, with a voltmeter across the component, and record the current for a range of potential differences.

Comparing ohmic and non-ohmic components

  1. Set up the circuit

    Put the component in series with an ammeter, a switch and a variable supply, and connect a voltmeter across the component.

  2. Take readings across the range

    Start at a low potential difference and increase it in even steps, recording V and I each time. Aim for at least six readings.

  3. Reverse the connections

    Swap the supply leads and repeat. A resistor or lamp behaves the same both ways; a diode doesn't.

  4. Control the temperature where you can

    For the resistor, keep currents small and switch off between readings so it stays at room temperature.

  5. Plot and compare

    Plot I against V for each component, then compare the shapes and calculate V divided by I at several points.

Exam tip

Describing a characteristic

Name the shape and say what it means. "The graph is a straight line through the origin, so the current is directly proportional to the potential difference and the resistance is constant: the resistor is ohmic." Or: "The gradient decreases as V increases, so each extra volt adds less current: the lamp's resistance increases."

Summary

  • Ohmic: I∝VI \propto V at constant temperature, so RR is constant and the I–V graph is a straight line through the origin.

  • Non-ohmic: the resistance changes with VV or II, so the graph is not a straight line through the origin. Filament lamps, diodes and thermistors are examples.

  • At any point, R=VIR = \dfrac{V}{I}, never the gradient of the curve.

  • A filament lamp's resistance rises as it heats, because its more strongly vibrating ions cause more collisions.

  • To compare components experimentally, measure V and I over a range of values, in both directions, and plot the characteristics.

Finished the lesson?

Try the 2 quick checks above and the lesson completes itself, or mark it complete now.

Lesson 5 of 100% read

Save your progress with a free account