Lesson 10 of 10 · 17 min
Gas volumes and masses in chemical reactions
Combine the mole ratio from a balanced equation with molar volume or to calculate the volume of a gas made or used in a reaction, or the mass of a reactant needed.
What you will be able to do
- Use a balanced equation to convert moles of one substance into moles of a gas.
- Calculate the volume of a gas produced or consumed at STP, or at any stated conditions with .
- Calculate the mass of a reactant or product from a gas volume.
- Use volume ratios directly for gases measured at the same temperature and pressure.
A car airbag must fill in about 30 milliseconds to the right size: too little gas and it does not protect, too much and it bursts. Engineers choose the mass of solid that reacts to make the gas with exactly the calculation in this lesson. You already know how to use a balanced equation to relate masses; gases just add one more conversion at the end.
The route from the mass of one substance to the volume of a gas, and back the other way.
Gas stoichiometry
Write the balanced equation
Check that it is balanced; the coefficients give the mole ratio.
Find the moles of the substance you know
for a mass; for a gas at STP; for a gas at other conditions.
Use the mole ratio
Convert to what the question asks for
at STP, at other conditions, or .
Worked example
Volume of carbon dioxide from heating limestone
Calcium carbonate decomposes when heated strongly:
Calculate the volume of carbon dioxide, measured at STP, produced when 25.0 g of calcium carbonate decomposes completely.
Step 1: Molar mass of calcium carbonate
Step 2: Moles of calcium carbonate
Step 3: Mole ratio
From the equation, 1 mol gives 1 mol , so .
Step 4: Volume at STP
Try it yourself first, then check the working one step at a time.
Answer
5.67 L of carbon dioxide at STP.
Method
Moles of the known substance from its mass.
Mole ratio from the balanced equation.
Volume at STP = moles × 22.7 L mol⁻¹.
Watch out for
Converting 25.0 g straight to a volume without finding moles.
Rounding the moles to 0.25 too early (the answer still rounds to 5.67 L here, but it often will not).
Zinc reacts with excess hydrochloric acid: . What volume of hydrogen, measured at STP, is produced from 1.50 g of zinc? Give your answer in L to three significant figures.
When the gas is not at STP, find its moles with (or its volume with ) instead of using 22.7 L mol⁻¹. The mole-ratio step is the same.
Worked example
Mass of magnesium to make hydrogen at room conditions
A student needs 250 mL of hydrogen gas, measured at 22 °C and 101 kPa, from the reaction
Calculate the minimum mass of magnesium needed, with excess acid.
Step 1: Convert the units
, ,
Step 2: Moles of hydrogen
The gas is not at STP, so use :
22.7 L mol⁻¹ only applies at 273 K and 100 kPa; at 295 K and 101 kPa a mole of gas occupies about 24.3 L.
Step 3: Mole ratio
1 mol Mg gives 1 mol , so .
Step 4: Mass of magnesium
Try it yourself first, then check the working one step at a time.
Answer
At least 0.250 g of magnesium.
Method
for the gas (kelvin, kPa, L).
Mole ratio from the equation.
.
Watch out for
Using 22.7 L mol⁻¹ at 22 °C, which gives 0.268 g, about 7 % too much.
Using the 2 in front of HCl as the ratio for hydrogen.
Gases reacting with gases. Because equal volumes of gases at the same temperature and pressure contain equal numbers of moles, the coefficients of gases in an equation are also their volume ratios, as long as every volume is measured at the same temperature and pressure. You do not need to convert to moles at all.
Burning 1.0 L of methane uses 2.0 L of oxygen and makes 1.0 L of carbon dioxide (at the same conditions; the water condenses to a liquid).
Propane burns completely: . What volume of oxygen is needed to burn 2.00 L of propane, both volumes measured at the same temperature and pressure?
Worked example
How much sodium azide fills an airbag?
In some airbags, a spark sets off the rapid decomposition of sodium azide:
A driver's airbag must fill to 60.0 L with nitrogen at 125 kPa and 30 °C.
(a) Calculate the mass of sodium azide needed.
(b) The sodium produced is hazardous. Suggest why the airbag also contains potassium nitrate and silicon dioxide, and why an engineer would add slightly more sodium azide than calculated.
Step 1: Moles of nitrogen needed
.
Step 2: Mole ratio
2 mol gives 3 mol , so
Write the ratio as wanted over known: .
Step 3: Mass of sodium azide
, so
Step 4: Think about the real device (b)
Sodium is a reactive metal that reacts violently with water (including moisture in the air) to form corrosive sodium hydroxide. Potassium nitrate reacts with the sodium to make more nitrogen and metal oxides, and silicon dioxide turns those oxides into harmless glass. A little extra azide allows for the gas cooling as the bag fills, some gas escaping through the bag's vents, and the reaction not being perfectly complete.
Try it yourself first, then check the working one step at a time.
Answer
(a) About 129 g of sodium azide. (b) To convert the reactive sodium into harmless products (and extra nitrogen); extra azide allows for incomplete reaction, gas loss and cooling.
Method
for the gas at the stated conditions.
Mole ratio wanted ÷ known.
, then judge the answer against the real situation.
Watch out for
Using the ratio the wrong way round: gives 291 g.
Using 22.7 L mol⁻¹ even though the gas is at 125 kPa and 30 °C.
Common mistake
Where gas stoichiometry goes wrong
- Using the mole ratio the wrong way up. Write it as every time.
- Using 22.7 L mol⁻¹ when the gas is at room temperature, or using volume ratios for a gas and a solid or liquid. Volume ratios are only for gases at the same conditions.
- Applying molar volume to water when it is a liquid product.
- Rounding the moles to one or two figures part-way through. Keep at least four significant figures until the end.
Exam tip
Marks for each step
In a 3–4 mark gas stoichiometry question there is usually a mark for the moles of the known substance, one for the mole ratio, and one for the final volume or mass with its unit. Label each line () so the marker can follow it even if a number slips.
Summary
Route: mass → moles (÷ M) → mole ratio → moles of gas → volume (× 22.7 at STP, or ), and the reverse.
Away from STP, use for the gas, with kelvin and kPa with L.
For gases at the same temperature and pressure, the volume ratio equals the mole ratio from the equation.
Keep full values between steps; round only the final answer.
Finished the lesson?
Try the 2 quick checks above and the lesson completes itself, or mark it complete now.