Lesson 4 of 11 · 17 min
Reflection, refraction and diffraction
Describe how waves reflect from fixed and free ends, what is reflected and transmitted at a boundary between two media, why waves refract, and when they diffract.
What you will be able to do
- Describe the reflection of a pulse from a fixed end and from a free end.
- Describe the reflected and transmitted waves at a boundary between two media, and state what changes and what stays the same.
- Describe refraction as a change of direction caused by a change of speed.
- Describe diffraction and the conditions under which it is most noticeable.
Shout towards a cliff and the sound comes back as an echo. Watch waves roll into a harbour and they bend around the breakwater. Listen through an open door and you hear people you can't see. Waves meeting boundaries and obstacles do four things: they reflect, transmit, refract and diffract.
Send a pulse towards the end. Compare what comes back from a fixed end (tied to a wall) with what comes back from a free end (a ring that can slide up and down a pole).
Key idea
Fixed and free ends
- At a fixed end, the reflected pulse is inverted. The upward pulse pulls up on the wall; the wall pulls down on the spring (Newton's third law) and sends back a downward pulse.
- At a free end, the reflected pulse is upright. The end flicks up freely and pulls the spring back up behind it.
In both cases the reflected pulse has the same speed and width as the incident pulse, because it travels in the same medium.
Join a light spring to a heavy spring and send a pulse along. At the join, part of the pulse is transmitted and part is reflected. The heavy spring behaves partly like a fixed end, and the light spring partly like a free end:
| Pulse travels from… | Reflected pulse | Transmitted pulse |
|---|---|---|
| Light (fast) spring to heavy (slow) spring | Inverted, smaller | Upright, smaller, slower and shorter |
| Heavy (slow) spring to light (fast) spring | Upright, smaller | Upright, faster and longer |
Key idea
What changes at a boundary
For a continuous wave crossing a boundary, the frequency stays the same (each bit of the boundary oscillates at the frequency of the arriving wave). The speed changes, so the wavelength changes in the same proportion:
A pulse on a light spring reaches a join with a much heavier spring. Which describes the reflected pulse?
Worked example
A wave passes from a light spring into a heavy spring
A continuous wave of frequency travels at along a light spring. The light spring is joined to a heavy spring, in which waves travel at .
(a) Calculate the wavelength on the light spring.
(b) State the frequency, and calculate the wavelength, of the wave on the heavy spring.
(c) Describe the wave reflected at the join.
Step 1: Wavelength on the light spring
Step 2: Frequency on the heavy spring
The frequency is set by the source and does not change at the boundary: .
Each coil at the join is driven up and down by the arriving wave, at the arriving wave's frequency.
Step 3: Wavelength on the heavy spring
Step 4: Describe the reflected wave
Going from a light (fast) spring to a heavy (slow) one is like meeting a fixed end, so the reflected wave is inverted. It travels back along the light spring, so it has the same speed (), frequency () and wavelength () as the incident wave, but a smaller amplitude, because some energy is transmitted.
Try it yourself first, then check the working one step at a time.
Answer
(a) (b) and (c) The reflected wave is inverted, has the same frequency, speed and wavelength as the incident wave, and a smaller amplitude.
Method
Use in each medium with the same frequency.
Light-to-heavy reflections are inverted; heavy-to-light reflections are upright.
The reflected wave keeps the speed and wavelength of the medium it travels in.
Watch out for
Changing the frequency at the boundary.
Giving the reflected wave the heavy spring's wavelength. It never enters the heavy spring.
Refraction happens when a wave crosses a boundary at an angle and changes speed. Water waves slow down as they move from deep into shallow water. The end of each wavefront that reaches the shallow water first slows first, so the wavefront swings round and the wave changes direction. Slowing down bends the wave towards the normal, the line at right angles to the boundary.
Wavefronts crossing into shallower water, where the waves travel 0.6 times as fast. Frequency is unchanged, so the wavelength shrinks to 0.6 of its value and the direction bends towards the normal.
Tip
Speeding up bends away
Slowing down bends a wave towards the normal; speeding up bends it away from the normal. A wave that meets the boundary head-on (along the normal) changes speed and wavelength but not direction.
Diffraction is the spreading of a wave as it passes through a gap or around the edge of an obstacle. How much a wave spreads depends on the size of the gap compared with the wavelength. When the gap is about the same size as the wavelength, the wave spreads out into almost circular wavefronts. When the gap is much wider than the wavelength, most of the wave passes straight through and only the edges bend.
Diffraction is strongest when the gap is about one wavelength wide (left). Through a gap much wider than the wavelength (right), the wave barely spreads.
You can hear people talking in the next room through an open doorway, but you can't see them. Which statement best explains this?
Note
Engineering with reflection and absorption
Acoustical engineers control noise pollution by controlling reflection. Soft, porous panels in cinemas and recording studios absorb sound energy instead of reflecting it, cutting echoes. Concert halls are shaped so reflections reach every seat evenly instead of focusing sound in some spots. Concrete noise barriers beside motorways reflect traffic noise back towards the road and away from houses — and they work better the taller they are, because low-frequency sound diffracts over the top.
Tip
In the lab
You can see all of this with a slinky and a rope. Send a pulse to an end held firmly (fixed) and to an end tied to a light thread (nearly free) and compare the reflections. Join two springs of different mass and watch a pulse split at the join, using both side-to-side (transverse) and push–pull (longitudinal) pulses. Slow-motion phone video makes the inversion easy to see.
Summary
A pulse reflected from a fixed end is inverted; from a free end it is upright.
At a boundary between two media, part of a wave is reflected and part transmitted. Going into a slower medium, the reflection is inverted; the transmitted wave is always upright.
Crossing a boundary, frequency stays the same while speed and wavelength change together: .
Refraction is a change of direction caused by a change of speed: slowing down bends a wave towards the normal.
Diffraction is the spreading of waves through gaps and around obstacles, strongest when the gap is about one wavelength wide.
Absorbing surfaces and carefully shaped reflecting surfaces let engineers reduce noise pollution.
Finished the lesson?
Try the 2 quick checks above and the lesson completes itself, or mark it complete now.