Lesson 11 of 11 · 13 min
Intensity and the inverse-square law
Describe intensity as power per unit area, relate it to the square of the amplitude, and use to compare the intensity of light at different distances from a source.
What you will be able to do
- Describe intensity as the power carried per unit area.
- Use the proportionality between intensity and the square of the amplitude, .
- Explain the inverse-square law for a point source and solve problems with .
A desk lamp lights up the page in front of you, but from across the room the same lamp barely lights a book at all. The lamp has not changed — the light has spread out. Intensity measures how concentrated the energy of a wave is where you are.
Definition
Intensity
The intensity of a wave is the power it carries per unit area, measured on a surface at right angles to the direction of travel:
Brighter light and louder sound have higher intensity.
Intensity also depends on how hard the medium (or, for light, the electric field) is oscillating. The energy of an oscillation is proportional to the square of its amplitude, so intensity is too:
Double the amplitude of a wave and its intensity becomes times greater; halve the amplitude and the intensity drops to a quarter.
The amplitude of a wave is tripled. By what factor does its intensity change?
Now think about a small lamp — a point source — sending light out equally in every direction. At distance , its power is spread over the surface of a sphere of area . At twice the distance, the same power covers a sphere with four times the area, so each square metre gets a quarter as much. At three times the distance, a ninth.
Intensity falls with the square of the distance: doubling quarters ; tripling divides it by 9.
Key idea
The inverse-square law
For a point source, intensity is inversely proportional to the square of the distance:
Check the direction of your answer: further away means lower intensity.
Worked example
Intensity further from a lamp
A light sensor from a small lamp measures an intensity of . Calculate the intensity from the lamp.
Step 1: Write the inverse-square relationship
means is constant.
Step 2: Substitute
Step 3: Check the direction
The sensor moved times further away, so the intensity fell by times: . Further away, dimmer — reasonable.
Try it yourself first, then check the working one step at a time.
Answer
Method
.
Check the answer is smaller when the distance increases.
Watch out for
Using without squaring, giving .
Inverting the ratio, which makes the light brighter further away.
A light sensor from a small lamp measures . What does it measure when moved to from the lamp?
Worked example
Sunlight on Mars
The intensity of sunlight just above Earth's atmosphere is . Earth is from the Sun and Mars is from the Sun.
(a) Calculate the intensity of sunlight at Mars.
(b) A solar panel on Mars must collect the same power as a panel above Earth's atmosphere. What area does it need?
Step 1: Treat the Sun as a point source
At these distances the Sun is effectively a point source, so .
Step 2: Calculate the intensity at Mars
Step 3: Relate power, intensity and area
Power collected intensity area. For equal power, .
Step 4: Calculate the area
The intensity ratio is the inverse of the squared distance ratio, so the area must grow by .
Try it yourself first, then check the working one step at a time.
Answer
(a) (b) About
Method
Use the ratio of distances, squared.
Power = intensity × area.
Watch out for
Forgetting to square the ratio: is wrong.
Common mistake
When the inverse-square law applies
is for a point source sending energy out equally in all directions, with nothing absorbing it on the way. A laser beam hardly spreads, so its intensity barely changes with distance. A long fluorescent tube is not a point source up close. And in fog or murky water, absorption makes the intensity fall faster still.
Tip
Testing the law in the lab
Measure the intensity from a small bulb with a light sensor at several distances, in a darkened room. To test , check that is constant, or plot against : the law predicts a straight line through the origin. Measure to the filament, not to the glass.
Summary
Intensity is the power per unit area, in .
Intensity is proportional to amplitude squared: .
For a point source, the power spreads over a sphere of area , so and .
Doubling the distance quarters the intensity; tripling it divides the intensity by 9.
A plot of against is a straight line through the origin if the inverse-square law holds.
Finished the lesson?
Try the 2 quick checks above and the lesson completes itself, or mark it complete now.