Lesson 5 of 11 · 18 min

Superposition, interference and standing waves

Use the principle of superposition to find resultant amplitudes, explain constructive and destructive interference, and explain how standing waves form with nodes and antinodes.

What you will be able to do

  • State the principle of superposition and use it to find the resultant displacement of overlapping waves or pulses.
  • Explain constructive and destructive interference, and find resultant amplitudes A1+A2A_1 + A_2 and ∣A1−A2∣|A_1 - A_2|.
  • Explain the formation of a standing wave in terms of superposition, with nodes and antinodes.

Send a pulse along each end of a rope at the same time. You might expect them to crash and bounce off each other. Instead they pass straight through each other and carry on, unchanged. While they overlap, though, the rope takes a shape that neither pulse has on its own.

Definition

The principle of superposition

When two or more waves meet, the resultant displacement at each point is the sum of the individual displacements at that point, taking direction into account (up positive, down negative). After they have passed, each wave continues as if the other had never been there.

Two upward pulses overlapping: pulse 1 (dashed blue, 2 cm high) and pulse 2 (dashed green, 1 cm high). The rope's actual shape (solid) is found by adding their displacements point by point.

Interactive

Add two waves

Slide one wave along the other. Where crest meets crest, the resultant is tallest. Where crest meets trough, the waves cancel.

Key idea

Constructive and destructive interference

  • Constructive interference: the waves arrive in phase (crest on crest, trough on trough). The resultant amplitude is the sum: A=A1+A2A = A_1 + A_2.
  • Destructive interference: the waves arrive half a cycle out of phase (crest on trough). The resultant amplitude is the difference: A=∣A1−A2∣A = |A_1 - A_2|. Equal amplitudes cancel completely.

For any other phase difference, the resultant amplitude lies between these two values.

Two waves of the same frequency, with amplitudes 3 cm3\unit{cm} and 5 cm5\unit{cm}, meet. Find the resultant amplitude when they are in phase, and when they are exactly half a cycle out of phase (in cm).

Interference happens wherever waves overlap. Two loudspeakers playing the same note in phase send sound waves across a room. At a point where the two path lengths differ by a whole number of wavelengths (0,λ,2λ,…0, \lambda, 2\lambda, \dots), the waves arrive in phase and interfere constructively: the sound is loud. Where the paths differ by an odd number of half-wavelengths (λ2,3λ2,…\frac{\lambda}{2}, \frac{3\lambda}{2}, \dots), they arrive out of phase and interfere destructively: the sound is quiet. Walk across the room and you hear it rise and fall.

Worked example

Loud or quiet? Interference from two speakers

  • Complex familiar

Two loudspeakers, A and B, are connected to the same signal generator, so they emit sound in phase at 692 Hz692\unit{Hz}. The air is at 25 °C. A microphone at point P is 4.00 m4.00\unit{m} from A and 5.25 m5.25\unit{m} from B.

(a) Determine whether P is a point of constructive or destructive interference.

(b) Calculate the lowest frequency for which P would be a point of constructive interference.

6 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Find λ=vf\lambda = \frac{v}{f}.

  2. Find the path difference and divide by the wavelength.

  3. Whole number → constructive; whole number plus a half → destructive.

Watch out for

  • Comparing the distances themselves instead of their difference.

  • Choosing m=0m = 0 for part (b): a zero path difference is impossible here because P is closer to A.

Now send a continuous wave along a rope tied to a wall. It reflects from the fixed end, so two identical waves — same frequency, same amplitude — travel along the rope in opposite directions and superpose. At the right frequencies, the result is a standing wave: a pattern that oscillates in place but does not travel along the rope.

Interactive

A standing wave

Some points never move (nodes); others swing with the largest amplitude (antinodes). Change the harmonic and count the nodes.

Definition

Nodes and antinodes

  • A node is a point where the two travelling waves always arrive half a cycle out of phase, so they always interfere destructively: the displacement is always zero.
  • An antinode is a point where they always arrive in phase, so they always interfere constructively: the medium vibrates with the largest amplitude (twice that of each travelling wave).

Adjacent nodes are half a wavelength apart, and so are adjacent antinodes. A node and the next antinode are a quarter of a wavelength apart.

Adjacent nodes on a standing wave are 0.35 m0.35\unit{m} apart. What is the wavelength of the travelling waves that form it?

in m

Give 2 significant figures.

Exam tip

Explaining a standing wave

A full answer to "explain how a standing wave forms" has four parts: (1) two waves of the same frequency and amplitude travel in opposite directions (usually a wave and its reflection); (2) they superpose; (3) at nodes they always interfere destructively, so there is no displacement; (4) at antinodes they always interfere constructively, so the amplitude is greatest.

Which statement about a standing wave on a string is correct?

Choose one answer

Summary

  • Superposition: where waves overlap, the resultant displacement is the sum of the individual displacements. Waves pass through each other unchanged.

  • In phase gives constructive interference, A=A1+A2A = A_1 + A_2; half a cycle out of phase gives destructive interference, A=∣A1−A2∣A = |A_1 - A_2|.

  • From two in-phase sources, a path difference of a whole number of wavelengths gives constructive interference; an odd number of half-wavelengths gives destructive.

  • A standing wave forms when two identical waves travel in opposite directions and superpose. Nodes (always destructive) do not move; antinodes (always constructive) vibrate the most.

  • Adjacent nodes are λ2\frac{\lambda}{2} apart; a node to the next antinode is λ4\frac{\lambda}{4}.

Finished the lesson?

Try the 3 quick checks above and the lesson completes itself, or mark it complete now.

Lesson 5 of 110% read

Save your progress with a free account