Lesson 5 of 10 · 20 min

Measuring specific heat capacity

Analyse a specific heat capacity experiment, find c from the gradient of a graph, record measurements with uncertainties and evaluate the result with percentage error.

What you will be able to do

  • Describe a method for measuring the specific heat capacity of a substance with an electric heater.
  • Show that energy supplied and temperature change are proportional, and find cc from the gradient of a graph.
  • Record measurements with a symbol, value, absolute and percentage uncertainty and SI unit, and combine uncertainties.
  • Compare analogue and digital thermometers, and explain why heat loss makes a measured cc too high.

Data tables say the specific heat capacity of aluminium is about 900 J kg−1 K−1900\ \mathrm{J\,kg^{-1}\,K^{-1}}. How would you check that for yourself? You need a known mass, a known amount of energy, and a temperature change you can measure. This lesson is the practical behind Q=mcΔTQ = mc\Delta T, and the skills you use to analyse it.

A typical set-up. A joulemeter measures the energy supplied directly; otherwise, use Q=PtQ = Pt.

Method

  1. Measure the mass of the block

    Use an electronic balance and record it with its uncertainty, for example m=(1.000±0.001) kgm = (1.000 \pm 0.001)\ \mathrm{kg}.

  2. Set up the heater and thermometer

    Put the heater and thermometer in the holes in the block, with a few drops of oil in the thermometer hole for good thermal contact. Wrap the block in insulation.

  3. Record the starting temperature

    Wait until the reading is steady, then record TiT_i with its uncertainty.

  4. Heat and record

    Switch on the heater and start the stopwatch. Record the temperature every 60 s, and the energy supplied from the joulemeter (or the power and the time).

  5. Find the highest temperature

    Switch off after about 10 minutes but keep reading. The temperature keeps rising briefly while energy spreads from the heater through the block; use the highest reading as TfT_f.

  6. Repeat

    Let the block cool and repeat at least twice more, then average your results.

For a fixed mass of one substance, Q=mcΔTQ = mc\Delta T says that ΔT=1mc Q\Delta T = \frac{1}{mc}\,Q: the temperature rise is directly proportional to the energy supplied. A graph of ΔT\Delta T (dependent variable, yy-axis) against QQ (independent variable, xx-axis) should be a straight line through the origin with gradient 1mc\frac{1}{mc}.

If the heater supplies a constant power PP, then Q=PtQ = Pt, and a graph of temperature against time is a straight line with gradient Pmc\frac{P}{mc}. Either way, the gradient gives you cc.

Interactive

Energy supplied and temperature rise

Results for 0.200 kg of water heated in an insulated cup. Is the relationship proportional? Drag a point to see how one bad reading changes the gradient.

For the 0.200 kg of water in the graph above, the line of best fit has a gradient of 1.10 K kJ−11.10\ \mathrm{K\,kJ^{-1}}. Determine the specific heat capacity of water from these results, to three significant figures.

in J kg -1 K -1

Give 3 significant figures.

Worked example

Finding specific heat capacity from a temperature–time graph

  • Complex familiar
  • Technology active

A student heats an insulated 1.00 kg aluminium block with a 50.0 W heater and records its temperature every 60 s. The graph shows the data and the line of best fit, which passes through (0 s, 21.0 °C) and (600 s, 52.2 °C).

(a) Determine the gradient of the line of best fit.

(b) Determine the specific heat capacity of aluminium from the experiment.

(c) The accepted value is 900 J kg−1 K−1900\ \mathrm{J\,kg^{-1}\,K^{-1}}. Calculate the percentage error and explain the direction of the error.

Temperature of the aluminium block while the 50.0 W heater is on.

5 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Take the gradient from two well-separated points on the line of best fit.

  2. Match the gradient to the formula: for a T–t graph, gradient = P/(mc).

  3. Rearrange for c, then compare with the accepted value.

Watch out for

  • Using one data point, such as c=Ptm Tc = \frac{Pt}{m\,T} with the temperature instead of the temperature change.

  • Saying the error is "human error". Name the physical cause: energy lost to the surroundings.

Key idea

Recording and combining uncertainties

Record every measurement with its symbol, value, absolute uncertainty and SI unit, such as m=(0.250±0.001) kgm = (0.250 \pm 0.001)\ \mathrm{kg} or T=(23.5±0.5) ∘CT = (23.5 \pm 0.5)\ ^\circ\mathrm{C}.

  • Analogue scale (such as a liquid-in-glass thermometer): usually ± half the smallest division.
  • Digital readout: usually ± one unit in the last digit.
  • Repeated trials: Δxˉ=±xmax⁡−xmin⁡2\Delta\bar{x} = \pm\dfrac{x_{\max} - x_{\min}}{2}.
  • Percentage uncertainty =absolute uncertaintymeasurement×100 %= \dfrac{\text{absolute uncertainty}}{\text{measurement}} \times 100\ \%.

When you add or subtract measurements (such as ΔT=Tf−Ti\Delta T = T_f - T_i), add their absolute uncertainties. When you multiply or divide (such as c=QmΔTc = \frac{Q}{m\Delta T}), add their percentage uncertainties.

Analogue thermometer

  • Liquid-in-glass, marked every 1 °C, so read to ±0.5 °C.
  • The reading depends on your eye: parallax error if you don't read at eye level.
  • Slow to respond when the temperature changes quickly.

Digital thermometer

  • Displays 0.1 °C, so ±0.1 °C: more precise.
  • No parallax, and it can log data automatically.
  • Responds quickly. But extra decimal places do not guarantee accuracy: a poorly calibrated probe can be precisely wrong.

Definition

Precision, accuracy and two kinds of error

  • Precision: how close repeated measurements are to each other.
  • Accuracy: how close a measurement is to the true value. Check a thermometer's accuracy against fixed points such as melting ice (0 °C) and boiling water (close to 100 °C at sea level).
  • Random error scatters readings both ways. Repeating and averaging reduces its effect.
  • Systematic error shifts every reading the same way, such as energy lost to the surroundings or a thermometer that reads 0.8 °C high. Repeating does not help; you must improve the method or calibrate the instrument.

Worked example

Mean and uncertainty from repeated trials

  • Simple familiar
  • Technology active

Five trials of the same heating experiment gave these temperature rises: 12.4 K, 12.9 K, 12.6 K, 13.0 K and 12.6 K.

(a) Calculate the mean temperature rise.

(b) Calculate the absolute uncertainty of the mean.

(c) Calculate the percentage uncertainty, and record the result.

4 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Mean = sum of trials ÷ number of trials.

  2. Absolute uncertainty of the mean = ± (max − min)/2.

  3. Percentage uncertainty = absolute uncertainty ÷ mean × 100 %.

  4. Record value ± uncertainty with the unit, to matching decimal places.

Watch out for

  • Using the full range (0.6 K) as the uncertainty instead of half of it.

  • Giving the mean to more decimal places than the uncertainty, such as 12.70 ± 0.3 K.

An experiment records Ti=(21.0±0.5) ∘CT_i = (21.0 \pm 0.5)\ ^\circ\mathrm{C} and Tf=(46.0±0.5) ∘CT_f = (46.0 \pm 0.5)\ ^\circ\mathrm{C}. Calculate the percentage uncertainty in the temperature change, to two significant figures.

in \%

Give 2 significant figures.

Common mistake

Which way does heat loss push the answer?

If you calculate c=QmΔTc = \frac{Q}{m\Delta T} using the energy supplied, energy lost to the surroundings makes ΔT\Delta T smaller than it should be, so your cc comes out too high.

Don't write "human error". Name the cause and its direction: "energy transferred to the surroundings by conduction and convection, which makes the calculated cc larger than the true value". Insulating the block (and putting a lid on a liquid) reduces this systematic error; repeating the experiment does not.

In a specific heat capacity experiment, which change would most reduce the systematic error caused by energy loss to the surroundings?

Choose one answer

Exam tip

Data-test habits

QCAA questions often give a graph from an experiment. Say what the gradient represents before you use it: for a TT–tt graph with constant power, gradient =Pmc= \frac{P}{mc}; for ΔT\Delta T against QQ, gradient =1mc= \frac{1}{mc}. Take the gradient from the line of best fit, not two data points.

Keep percentage uncertainty (the spread of your own measurements) separate from percentage error (how far your result is from the accepted value).

Summary

  • Measure mm, the energy supplied (Q=PtQ = Pt or a joulemeter) and ΔT\Delta T; insulate, stir or use good thermal contact, and take the highest temperature.

  • For a fixed mass, ΔT∝Q\Delta T \propto Q. The gradient of ΔT\Delta T against QQ is 1mc\frac{1}{mc}; of TT against tt is Pmc\frac{P}{mc}.

  • Record measurements as value ± absolute uncertainty with unit. Add absolute uncertainties when adding or subtracting; add percentage uncertainties when multiplying or dividing.

  • A digital thermometer is more precise than an analogue one, but either can be inaccurate if it is not calibrated.

  • Energy loss to the surroundings is a systematic error that makes a measured cc too high; repeating does not remove it.

  • Percentage error compares your result with the accepted value.

Finished the lesson?

Try the 3 quick checks above and the lesson completes itself, or mark it complete now.

Lesson 5 of 100% read

Save your progress with a free account