Lesson 7 of 10 · 17 min
Heating curves and multi-stage problems
Read heating and cooling curves, and calculate the total energy or time needed to take a substance through several temperature changes and changes of state.
What you will be able to do
- Identify each section of a heating curve and explain its shape with the particle model.
- Relate the gradient of a sloping section and the length of a flat section to , , the mass and the heater power.
- Calculate the energy (or time) to take a substance through several stages, such as ice below 0 °C to steam above 100 °C.
Take 100 g of ice out of a freezer at −20 °C and heat it with a steady 200 W heater until it has all become steam. If you plot the temperature against time you get a heating curve: rising sections while the temperature of one state changes, and flat sections while the state changes. The shape tells you a lot about the physics, and the lengths of the sections can surprise you.
Heating curve for 0.100 kg of ice heated by a 200 W heater, assuming no energy losses, drawn to scale. Boiling (D) takes far longer than anything else.
| Section | What is happening | Particles | Energy for the stage |
|---|---|---|---|
| A | Ice warms from −20 °C to 0 °C | Vibrate faster: kinetic energy rises | |
| B | Ice melts at 0 °C | Break free of fixed positions: potential energy rises | |
| C | Water warms from 0 °C to 100 °C | Move faster: kinetic energy rises | |
| D | Water boils at 100 °C | Separate completely: potential energy rises | |
| E | Steam warms above 100 °C | Move faster: kinetic energy rises |
Change the heater power, then the mass. Which sections get longer or shorter? Which slopes change?
Key idea
Reading a heating curve with constant power
Sloping sections. In time the heater supplies , so the gradient is
A steeper slope means a smaller . Ice and steam () warm about twice as fast as liquid water ().
Flat sections. A change of state takes time , so a larger latent heat gives a longer plateau. Boiling (D) lasts about 6.8 times as long as melting (B), because .
On the heating curve above, why is section A (ice warming) steeper than section C (water warming)?
Solving a multi-stage problem
Sketch the path
Write the starting temperature, every change of state on the way (0 °C and 100 °C for water) and the final temperature.
One line per stage
Temperature change within one state: with that state's . Change of state: .
Add the stages
Keep full values until the end and round only the total.
Check it
For water, the change-of-state stages (especially boiling) usually dominate. If your total doesn't reflect that, look for a missing stage.
Times, if a heater is involved
With a constant power , each stage takes .
Worked example
From ice at −15 °C to steam at 110 °C
Calculate the total energy needed to turn 0.200 kg of ice at −15.0 °C into steam at 110 °C.
Step 1: Map out the stages
Ice warms from −15.0 °C to 0 °C → ice melts at 0 °C → water warms from 0 °C to 100 °C → water boils at 100 °C → steam warms from 100 °C to 110 °C. That is five stages.
Each stage uses a different formula or a different value of . Listing them first stops you missing one.
Step 2: Warm the ice
Step 3: Melt the ice
Step 4: Warm the water
Step 5: Boil the water
Step 6: Warm the steam
Step 7: Add the stages
Try it yourself first, then check the working one step at a time.
Answer
About . Boiling alone is about 74 % of the total.
Method
List every stage from start to finish.
Temperature changes: with the for that state.
Changes of state: with or .
Add, keeping full values until the end.
Watch out for
Using for the ice or steam stages.
Treating −15 °C to 110 °C as one temperature change of 125 K.
How much energy is needed to turn 0.0500 kg of ice at 0 °C into water at 30.0 °C? Give your answer in kJ to three significant figures.
Worked example
Reading c and L from a heating curve
A 0.200 kg sample of a solid is heated by a 50.0 W heater. Assume all the heater's energy goes into the sample. The graph shows its temperature.
(a) State the melting point.
(b) Determine the specific heat capacity of the solid.
(c) Determine the specific latent heat of fusion.
(d) Is the specific heat capacity of the liquid greater or smaller than that of the solid? Justify using the graph.
Heating curve for the 0.200 kg sample with a 50.0 W heater.
Step 1: Read the melting point
The temperature stays constant at 80 °C between 300 s and 900 s while the solid melts. The melting point is 80 °C.
Step 2: Energy for the solid warming
From 0 s to 300 s the solid warms from 20 °C to 80 °C. and .
Step 3: Calculate c for the solid
Step 4: Calculate the latent heat
Melting lasts , so and .
Step 5: Compare the slopes
Solid: . Liquid: . With the same power and mass, the slope is , so the gentler slope means a larger . The liquid's specific heat capacity is greater (it works out to about ).
From , . Same and , so slope and are inversely related.
Try it yourself first, then check the working one step at a time.
Answer
(a) 80 °C (b) (c) (d) greater, because the liquid section is less steep.
Method
Flat section: over its duration, then .
Sloping section: , from the graph, then .
Compare slopes to compare specific heat capacities.
Watch out for
Reading times at the wrong ends of a section.
Using the temperature (80 °C) instead of the change (60 K).
Liquid candle wax is left to cool in a room. Its temperature falls, stays constant at about 60 °C for several minutes, then falls again. During the constant-temperature section, the wax is:
Common mistake
Multi-stage slips
- Missing a stage, most often warming the meltwater or the steam.
- Using for ice or steam.
- Treating the whole temperature range as one , straight through a change of state.
- Rounding each stage before adding.
Exam tip
A mark for every stage
Markers award marks stage by stage. Label each line ("warming the ice", "melting"…), show its own substitution, and keep unrounded values until the total. If a graph is given, read and write down the values at both ends of each section before you calculate.
Summary
A heating curve has sloping sections (temperature change within one state) and flat sections (changes of state at constant temperature).
With constant power, a sloping section has gradient : steeper means smaller .
A flat section lasts : boiling water takes about 6.8 times as long as melting the same ice.
Solve multi-stage problems one stage at a time, using (right for each state) and , then add.
On a cooling curve, flat sections are freezing or condensing, where latent heat is released at constant temperature.
Finished the lesson?
Try the 3 quick checks above and the lesson completes itself, or mark it complete now.