Lesson 6 of 10 · 17 min

Changes of state and specific latent heat

Explain why the temperature stays constant while a substance melts or boils, and use Q=mLQ = mL to calculate the energy for a change of state.

What you will be able to do

  • Explain, using internal energy and the kinetic particle model, why the temperature stays constant during a change of state.
  • Describe the specific latent heats of fusion and vaporisation.
  • Solve problems with Q=mLQ = mL, including finding LL from experimental data.
  • Explain cooling by evaporation and why water can be boiled in a paper cup.

Put a pot of water on a full flame. Once it is boiling, a thermometer in the water sits at 100 °C for as long as you keep heating, even though the burner is still pouring energy in. Where is all that energy going?

Interactive

Melting with the heater on

Watch the temperature while the ice melts. The heater is still on, so where does the energy go? Look at what the particles are doing.

Key idea

Why the temperature stays constant

During a change of state, the energy supplied does work against the attractive forces between the particles, pulling them apart. It increases their potential energy, not their kinetic energy.

Temperature measures the average kinetic energy of the particles, so the temperature stays constant until the change of state is complete. The internal energy still increases, because the potential energy part of it is rising.

Definition

Specific latent heat

The specific latent heat LL of a substance is the energy needed to change the state of 1 kg of it without changing its temperature. Its unit is J kg−1\mathrm{J\,kg^{-1}}.

  • Latent heat of fusion LfL_f: solid ↔ liquid. For water, Lf=3.34×105 J kg−1L_f = 3.34 \times 10^5\ \mathrm{J\,kg^{-1}}.
  • Latent heat of vaporisation LvL_v: liquid ↔ gas. For water, Lv=2.26×106 J kg−1L_v = 2.26 \times 10^6\ \mathrm{J\,kg^{-1}}.
Energy for a change of state at constant temperature
Q=mLQ = mL

The same energy comes back out when the change reverses. Freezing 1 kg of water releases 3.34×105 J3.34 \times 10^5\ \mathrm{J}, and condensing 1 kg of steam releases 2.26×106 J2.26 \times 10^6\ \mathrm{J}. That is why a scald from steam at 100 °C is far worse than one from water at 100 °C: the steam releases its latent heat on your skin as it condenses, before it even starts to cool.

Worked example

Energy to melt ice

  • Simple familiar
  • Technology active

(a) Calculate the energy needed to melt 250 g of ice that is already at 0 °C.

(b) How much energy is released when the same water freezes again at 0 °C?

4 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Convert mass to kg.

  2. Pick LfL_f for melting or freezing, LvL_v for boiling or condensing.

  3. Q=mLQ = mL; the same energy is released when the change reverses.

Watch out for

  • Using LvL_v for melting.

  • Leaving the mass as 250, which gives an answer 1000 times too large.

How much energy is needed to boil away 0.250 kg of water that is already at 100 °C? Give your answer in kJ to three significant figures.

in kJ

Give 3 significant figures.

Note

Why boiling takes so much more energy than melting

For water, LvL_v is about 6.8 times LfL_f. Melting only loosens the particles enough for them to slide past each other; they stay close together. Boiling separates them completely, so far more of the attraction between them must be overcome, and the expanding vapour must also push back the surrounding atmosphere.

Ice at 0 °C is melting in a warm room. What is happening to the particles of the ice?

Choose one answer

Note

Cooling by evaporation

At any temperature, some molecules at the surface of a liquid are moving fast enough to escape. They are the most energetic ones, so when they leave, the average kinetic energy of the molecules left behind falls and the liquid cools.

Each kilogram of water that evaporates from your skin takes about 2.4×106 J2.4 \times 10^6\ \mathrm{J} with it (a little more than at 100 °C). That is how sweating cools you, and a big reason wet clothes leave you shivering, especially in a breeze that carries the vapour away.

Why you can boil water in a paper cup over a fire

Paper only catches fire once it is heated to more than about 200 °C. While the cup holds water, the paper in contact with the water cannot get much hotter than the water, because energy is conducted from the paper into the water about as fast as the flame supplies it.

The water's high specific heat capacity means it warms slowly. Once it reaches 100 °C it boils, and then all the energy supplied goes into vaporising water, 2.26×106 J2.26 \times 10^6\ \mathrm{J} for every kilogram, while the temperature stays at 100 °C. So the wet paper stays far below its ignition temperature. The part of the cup above the waterline has no water to carry energy away, and that part can char or burn.

Worked example

Measuring the latent heat of vaporisation

  • Complex familiar
  • Technology active

A 500 W immersion heater keeps water boiling in an insulated beaker that stands on a digital balance. Once the water is boiling steadily, the balance reading falls by 50.0 g in 4.00 min.

(a) Estimate the specific latent heat of vaporisation of water from these results.

(b) Calculate the percentage error compared with the data book value.

(c) Explain why the experimental value is higher than the accepted value.

5 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Energy from a heater: Q=PtQ = Pt with tt in seconds.

  2. Mass vaporised from the balance reading, in kg.

  3. L=Q/mL = Q/m, then compare with the data book.

Watch out for

  • Using 4.00 instead of 240 s.

  • Measuring from the moment the heater is switched on, before the water boils, which adds the energy used to warm it.

Common mistake

Two latent heat errors

Using Q=mcΔTQ = mc\Delta T during a change of state: ΔT=0\Delta T = 0, so it predicts that no energy is needed, which is wrong. Use Q=mLQ = mL for the change of state.

Getting the unit wrong: LL is energy per kilogram, J kg−1\mathrm{J\,kg^{-1}}. There is no "per kelvin", because the temperature does not change.

Supplying 8.0 kJ of energy melts 40 g of wax that is at its melting point. Calculate the specific latent heat of fusion of the wax, to two significant figures.

in J kg -1

Give 2 significant figures.

Exam tip

The four phrases markers look for

For "explain why the temperature stays constant during a change of state", include all four ideas:

  1. The energy supplied increases the potential energy of the particles (it does work against the attractive forces between them).
  2. The average kinetic energy of the particles does not change.
  3. So the temperature stays constant.
  4. The internal energy increases.

Summary

  • During a change of state, energy changes the potential energy of the particles, not their average kinetic energy, so the temperature stays constant while the internal energy changes.

  • Specific latent heat is the energy to change the state of 1 kg at constant temperature, in J kg−1\mathrm{J\,kg^{-1}}.

  • Q=mLQ = mL, with Lf=3.34×105 J kg−1L_f = 3.34 \times 10^5\ \mathrm{J\,kg^{-1}} (melting, freezing) and Lv=2.26×106 J kg−1L_v = 2.26 \times 10^6\ \mathrm{J\,kg^{-1}} (boiling, condensing) for water.

  • Freezing and condensing release the same energy that melting and boiling absorb.

  • Evaporation removes the most energetic molecules, cooling what is left; that is how sweating cools you.

  • Boiling water keeps its container near 100 °C, which is why a paper cup of water survives a campfire.

Finished the lesson?

Try the 3 quick checks above and the lesson completes itself, or mark it complete now.

Lesson 6 of 100% read

Save your progress with a free account