Lesson 1 of 11 · 18 min
Yield, rate and the Haber process
Explain how the temperature, pressure and catalyst of the Haber process are chosen to balance equilibrium yield against rate, cost and safety, and write the equation for making ammonia.
What you will be able to do
- Write the equation for the Haber process, , with its enthalpy change.
- Distinguish the effect of a condition on equilibrium yield (Le Châtelier's principle) from its effect on rate (collision theory).
- Explain why the Haber process uses a compromise temperature, a high pressure and an iron catalyst.
- Explain why unreacted gases are recycled and ammonia is removed.
Plants need nitrogen to make proteins, and the air is 78 % nitrogen. The problem is the triple bond: at it is one of the strongest bonds in chemistry, so barely reacts. In 1909 Fritz Haber found conditions that turn nitrogen into ammonia fast enough to be worth doing, and Carl Bosch scaled it up. Today more than 150 million tonnes of ammonia a year feed the fertilisers that grow about half the world's food.
Key idea
The Haber process
Nitrogen comes from the air. Hydrogen comes mainly from natural gas by steam reforming, . The two gases are mixed in the mole ratio given by the equation.
Two separate questions decide the conditions, and you need both:
- Yield: how much ammonia is in the mixture once it reaches equilibrium. Le Châtelier's principle answers this.
- Rate: how quickly the mixture gets there. Collision theory answers this.
A plant wants a high yield and a high rate, at a reasonable cost and safely. The Haber reaction makes those goals pull against each other.
| Condition | Effect on equilibrium yield | Effect on rate | What the plant does |
|---|---|---|---|
| Higher temperature | Lower. The forward reaction is exothermic, so heating favours the endothermic reverse reaction and falls. | Higher. More collisions have at least the activation energy. | 400–450 °C: a compromise, fast enough with a catalyst while the yield is still acceptable. |
| Higher pressure | Higher. The forward reaction turns 4 mol of gas into 2 mol, so compressing the mixture favours the side with fewer gas particles. | Higher. Gas concentrations rise, so collisions are more frequent. | About 20 MPa (≈ 200 atm): higher would cost more to compress and need thicker, more expensive equipment, and is more dangerous. |
| Iron catalyst | No change. It speeds up the forward and reverse reactions equally. | Much higher. It gives a pathway with a lower activation energy. | Porous iron (with and promoters), so the lower temperature is still fast enough. |
| Removing ammonia | Higher. Lowering shifts the position of equilibrium to the right. | The forward rate continues while the reverse rate drops. | The gas leaving the reactor is cooled; ammonia liquefies and is run off. |
Set the temperature, the pressure and the catalyst, and watch the equilibrium yield and the rate. Which condition helps yield but hurts rate?
A Haber plant raises its reactor temperature from to . What happens?
Common mistake
A catalyst does not increase the yield
A catalyst lowers the activation energy for the forward and the reverse reaction, so it speeds both up by the same factor. The position of equilibrium, and so the equilibrium yield, is unchanged. What the catalyst does improve is the amount of ammonia made per hour, because equilibrium is reached much sooner. In an exam, say "a catalyst increases the rate but does not change the equilibrium yield".
Even with a catalyst, the gases spend only seconds in the reactor, so they never quite reach equilibrium. Each pass converts only about 15 % of the nitrogen and hydrogen to ammonia. That sounds poor, but nothing is wasted: the ammonia is condensed out, and the unreacted gases are recycled with fresh feed. After many passes about 98 % of the hydrogen ends up as ammonia.
A Haber plant. Removing liquid ammonia and recycling the unreacted gases turn a 15 % conversion per pass into an overall yield near 98 %.
Worked example
Explain the conditions of the Haber process
Ammonia is made by the Haber process, , . Industrial plants operate at about and with an iron catalyst. Explain why these conditions are chosen.
Step 1: Identify the features of the reaction that matter
The forward reaction is exothermic (), and 4 mol of gas on the left form 2 mol on the right. It is reversible and reaches equilibrium.
Every argument about yield comes back to these two facts.
Step 2: Temperature and yield
By Le Châtelier's principle, a lower temperature favours the exothermic forward reaction, so a low temperature gives a higher equilibrium yield of ammonia.
Step 3: Temperature and rate
A lower temperature means fewer collisions with at least the activation energy, so the rate is slow and equilibrium takes too long to reach.
Step 4: State the temperature compromise
About gives an acceptable yield at an acceptable rate.
Step 5: Pressure
A high pressure shifts the equilibrium towards the side with fewer gas particles (the ammonia side), increasing the yield, and also increases the rate because the gases are more concentrated. Pressure is limited to about because higher pressures need costly compressors and thick-walled equipment, use more energy and increase the risk of a dangerous failure.
Step 6: Catalyst
The iron catalyst provides a pathway with a lower activation energy, so equilibrium is reached much faster. It does not change the equilibrium yield, but it lets the plant use a lower temperature, where the yield is higher, at a useful rate.
Try it yourself first, then check the working one step at a time.
Answer
About balances the higher yield of a low temperature against the faster rate of a high one; about raises both yield and rate but is limited by cost and safety; the iron catalyst increases the rate without changing the yield, so a lower temperature is still fast enough.
Method
Note whether the forward reaction is exo- or endothermic, and compare moles of gas on each side.
For each condition, give its effect on yield (Le Châtelier) and on rate (collision theory).
Explain the compromise, including cost and safety.
Say what the catalyst does and does not change.
Watch out for
Saying the catalyst increases the yield.
Explaining the rate with Le Châtelier's principle.
Saying high pressure is "too expensive" without giving the reason: compressors, equipment strength, energy, safety.
Select all the statements that are true of the iron catalyst in the Haber process.
Exam tip
Explaining industrial conditions
For each condition write three things: its effect on yield with the reason (exothermic forward reaction; 4 mol of gas → 2 mol), its effect on rate with the reason (collision theory), and why the plant's choice is a compromise (an acceptable yield at an acceptable rate, cost of energy and equipment, safety). Don't use Le Châtelier's principle to explain a rate.
Summary
, : exothermic, and 4 mol of gas become 2 mol.
Low temperature favours yield but slows the rate, so about 400–450 °C is a compromise.
High pressure favours both yield and rate; about 20 MPa is limited by the cost and safety of compressing gases.
The iron catalyst increases the rate, not the yield, so a lower temperature is still fast enough.
Only about 15 % reacts per pass; ammonia is liquefied out and unreacted gases are recycled.
Finished the lesson?
Try the 2 quick checks above and the lesson completes itself, or mark it complete now.