Lesson 2 of 11 · 16 min

Sulfuric acid by the contact process

Write the equations for each step of the contact process and explain the temperature, pressure, excess air and vanadium(V) oxide catalyst used to make sulfur trioxide.

What you will be able to do

  • Write balanced equations with states for each step of the contact process.
  • Explain the temperature, pressure, excess oxygen and VX2OX5\ce{V2O5} catalyst chosen for 2 SOX2(g)+OX2(g)⇌2 SOX3(g)\ce{2SO2(g) + O2(g) <=> 2SO3(g)}.
  • Explain why sulfur trioxide is absorbed in concentrated sulfuric acid rather than in water.

More sulfuric acid is made than any other chemical. It goes into superphosphate fertilisers, the processing of metal ores, batteries and countless other products. At Mount Isa, sulfur dioxide that would otherwise pour out of the copper smelter's stack is captured and turned into sulfuric acid by the contact process, named for the way the gases react in contact with a solid catalyst.

The contact process in four steps

  1. Make sulfur dioxide

    Burn sulfur in air, S(s)+OX2(g)→SOX2(g)\ce{S(s) + O2(g) -> SO2(g)}, or collect SOX2\ce{SO2} from roasting or smelting sulfide ores.

  2. Oxidise it to sulfur trioxide (the equilibrium step)

    2 SOX2(g)+OX2(g)⇌2 SOX3(g)\ce{2SO2(g) + O2(g) <=> 2SO3(g)}, ΔH=−198 kJ mol−1\Delta H = -198\unit{kJ\,mol^{-1}}, over a vanadium(V) oxide catalyst, VX2OX5\ce{V2O5}.

  3. Absorb the sulfur trioxide in concentrated sulfuric acid

    SOX3(g)+HX2SOX4(l)→HX2SX2OX7(l)\ce{SO3(g) + H2SO4(l) -> H2S2O7(l)}. The product, HX2SX2OX7\ce{H2S2O7}, is oleum (fuming sulfuric acid).

  4. Dilute the oleum with water

    HX2SX2OX7(l)+HX2O(l)→2 HX2SOX4(l)\ce{H2S2O7(l) + H2O(l) -> 2H2SO4(l)}. Half the acid goes back to absorb more SOX3\ce{SO3}.

Common mistake

Why not add sulfur trioxide straight to water?

On paper SOX3(g)+HX2O(l)→HX2SOX4(l)\ce{SO3(g) + H2O(l) -> H2SO4(l)} works, and it is the overall result of steps 3 and 4. In practice the reaction is so exothermic that the water boils and the acid forms as a fine mist of droplets that is very hard to condense and escapes with the waste gas. Absorbing SOX3\ce{SO3} in concentrated HX2SOX4\ce{H2SO4} is smooth and complete. In an exam, write the oleum route.

Step 2 is the one that needs careful conditions. It looks a lot like the Haber reaction: it is exothermic, and 3 mol of gas become 2 mol. So the same reasoning applies, with one big difference: the yield is already very high at low pressure.

Conditions for 2 SOX2(g)+OX2(g)⇌2 SOX3(g)\ce{2SO2(g) + O2(g) <=> 2SO3(g)}, ΔH=−198 kJ mol−1\Delta H = -198\unit{kJ\,mol^{-1}}.
ConditionEffect on yieldEffect on rateWhat the plant does
TemperatureLower temperature favours the exothermic forward reaction.Higher temperature is faster; below about 400 °C the catalyst barely works.About 400–450 °C, with the gas cooled between catalyst beds because the reaction heats it up.
PressureHigher pressure favours the side with fewer gas particles (3 mol → 2 mol).Higher pressure is faster.Only slightly above atmospheric, 100–200 kPa (1–2 atm): enough to push gas through the plant. The conversion is already above 99 %, so compressing is not worth the cost.
Excess airExtra OX2\ce{O2} shifts the position of equilibrium to the right and uses up more of the valuable SOX2\ce{SO2}.Higher [OX2][\ce{O2}] is slightly faster.Air is cheap, so oxygen is supplied in excess of the 2 : 1 ratio.
VX2OX5\ce{V2O5} catalystNo change.Much faster.Pellets in three or four beds, so the gas meets a large surface area.
Interactive

The sulfur trioxide reactor

Compare how much the yield depends on temperature and on pressure. Why does the contact process not use high pressure like the Haber process?

Explain why the conversion of SOX2\ce{SO2} to SOX3\ce{SO3} in the contact process is carried out at only 100–200 kPa100\text{–}200\unit{kPa}, even though a higher pressure would increase the equilibrium yield.

Write it out as you would in an exam. Put maths between dollar signs, like $x^2 + 1$. Worth 1 mark.

0 / 4000

Worked example

Write the equations for the contact process

  • Simple familiar
  • Technology free

Describe, using balanced equations with state symbols, how sulfuric acid is made from sulfur by the contact process. Name the catalyst.

4 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Sulfur (or a sulfide ore) to SOX2\ce{SO2}.

  2. SOX2\ce{SO2} to SOX3\ce{SO3} over VX2OX5\ce{V2O5}, with ⇌\ce{<=>}.

  3. SOX3\ce{SO3} into concentrated HX2SOX4\ce{H2SO4} to form oleum.

  4. Oleum plus water gives sulfuric acid.

Watch out for

  • Writing SOX3+HX2O→HX2SOX4\ce{SO3 + H2O -> H2SO4} as the industrial step.

  • Forgetting the equilibrium arrow for SOX2\ce{SO2} to SOX3\ce{SO3}, or the coefficient 2.

Write the balanced equation, with state symbols, for the formation of oleum in the contact process.

Reads asYour answer shows here as chemistry.

Note

The same reasoning, different answers

Both the Haber process and the SOX2\ce{SO2} oxidation are exothermic with fewer moles of gas on the product side, so both use a compromise temperature of about 400–450 °C. They differ in pressure: the Haber reaction's yield is low at 1 atm, so high pressure is worth paying for; the contact reaction's yield is already high, so it isn't.

Summary

  • S(s)+OX2(g)→SOX2(g)\ce{S(s) + O2(g) -> SO2(g)}, then 2 SOX2(g)+OX2(g)⇌2 SOX3(g)\ce{2SO2(g) + O2(g) <=> 2SO3(g)} over VX2OX5\ce{V2O5} at about 450 °C and 100–200 kPa with excess air.

  • SOX3(g)+HX2SOX4(l)→HX2SX2OX7(l)\ce{SO3(g) + H2SO4(l) -> H2S2O7(l)}, then HX2SX2OX7(l)+HX2O(l)→2 HX2SOX4(l)\ce{H2S2O7(l) + H2O(l) -> 2H2SO4(l)}.

  • SOX3\ce{SO3} is not added to water directly: the reaction is too exothermic and forms an acid mist.

  • Low pressure is enough because the conversion already exceeds 99 %; excess air pushes it further.

  • The catalyst increases the rate, not the yield.

Finished the lesson?

Try the 2 quick checks above and the lesson completes itself, or mark it complete now.

Lesson 2 of 110% read

Save your progress with a free account