Lesson 11 of 12 · 17 min

Transformers and power transmission

Explain how a transformer works using Faraday's law, solve problems with the turns ratio and IpVp=IsVsI_pV_p = I_sV_s, and explain why electricity is transmitted at high voltage.

What you will be able to do

  • Explain how a transformer works in terms of Faraday's law and electromagnetic induction.
  • Solve problems with VpVs=NpNs\frac{V_p}{V_s} = \frac{N_p}{N_s} and IpVp=IsVsI_pV_p = I_sV_s.
  • Explain why electricity is transmitted at high voltage, and calculate power lost in transmission lines.

A transformer for a halogen downlight turns the 230 V230\ \mathrm{V} mains into 12 V12\ \mathrm{V}. At a power station, transformers do the opposite, raising tens of kilovolts to hundreds of kilovolts for the long trip across the state. Changing voltages like this is a transformer's job, and it works only because of electromagnetic induction.

A transformer: two coils on a shared iron core. The changing flux made by the primary passes through the secondary.

A transformer has two coils wound on a shared iron core. The primary coil is connected to an AC supply; the secondary coil is connected to the load. The two coils are not electrically connected. Energy crosses from one to the other through the changing magnetic field.

How a transformer works

  1. An alternating current flows in the primary coil

  2. It makes a magnetic field that keeps changing in size and direction

  3. The iron core carries this changing flux through the secondary coil

    The core concentrates the field so that nearly all the flux made by the primary also passes through the secondary.

  4. The changing flux induces an EMF in the secondary

    By Faraday's law, emf=−NsΔϕΔt\text{emf} = -N_s\frac{\Delta\phi}{\Delta t}.

  5. The output alternates at the supply frequency

    The induced EMF reverses each time the flux changes direction, so the output is AC at the same frequency as the input.

Key idea

Why the turns ratio sets the voltage

Every turn of both coils links the same changing flux, so the same EMF, ΔϕΔt\frac{\Delta\phi}{\Delta t}, is induced in each turn. The voltage across each coil is therefore proportional to its number of turns:

VpVs=NpNs\frac{V_p}{V_s} = \frac{N_p}{N_s}

A secondary with more turns than the primary steps the voltage up; one with fewer turns steps it down.

For an ideal transformer, with no energy losses, power in equals power out. So if the voltage steps up, the current steps down by the same factor.
IpVp=IsVsI_pV_p = I_sV_s
Interactive

Transformer

Change the number of turns on each coil. How does the output voltage depend on the ratio? What happens to the output current when the voltage is stepped up?

A transformer at a substation steps 11 kV11\ \mathrm{kV} up to 132 kV132\ \mathrm{kV}. What is the turns ratio NsNp\frac{N_s}{N_p}?

Common mistake

Transformers need AC, and don't make energy

A steady DC current in the primary makes a steady flux, and a steady flux induces nothing, so a transformer connected to DC gives no output (apart from a brief pulse when it is switched on or off).

A step-up transformer raises the voltage but lowers the current. At best, power out equals power in; it never creates energy.

Worked example

A step-down transformer for a lamp

  • Simple familiar
  • Technology active

A transformer powers a 12 V12\ \mathrm{V}, 50 W50\ \mathrm{W} halogen lamp from the 230 V230\ \mathrm{V} mains. Its primary coil has 1150 turns. Assuming the transformer is ideal, calculate:

(a) the number of turns on the secondary coil

(b) the current in the lamp

(c) the current drawn from the mains.

3 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Voltages are in the ratio of the turns: VpVs=NpNs\frac{V_p}{V_s} = \frac{N_p}{N_s}.

  2. Currents are in the inverse ratio, from IpVp=IsVsI_pV_p = I_sV_s.

Watch out for

  • Assuming the current steps down along with the voltage. In a step-down transformer the current steps up.

Real transformers are very efficient, often better than 95%, but not perfect. Energy is lost as heat in the resistance of the coils (I2RI^2R), as heat from eddy currents induced in the iron core itself, and because a little of the flux leaks out of the core and misses the secondary.

Building the core from thin, insulated sheets (laminations) cuts the eddy currents, because they can't flow across the insulating layers. The efficiency is the output power as a percentage of the input power.

An ideal transformer steps 230 V230\ \mathrm{V} down to 23 V23\ \mathrm{V}. The current in the secondary is 3.0 A3.0\ \mathrm{A}. Calculate the current in the primary.

in A

Give 2 significant figures.

Why transmit at high voltage? Transmission lines are long, so even thick cables have resistance, and they lose power as heat: Ploss=I2RP_{loss} = I^2R. For a given power P=VIP = VI, a higher voltage means a smaller current. Because the loss depends on the square of the current, raising the voltage ten times cuts the current ten times and the loss a hundred times.

Worked example

Why the grid transmits at high voltage

  • Complex unfamiliar
  • Technology active

A power station sends 50 MW50\ \mathrm{MW} to a city through transmission lines with a total resistance of 4.0 Ω4.0\ \Omega. Compare the power lost in the lines when the power is transmitted at 25 kV25\ \mathrm{kV} and at 250 kV250\ \mathrm{kV}, and explain why the grid uses step-up transformers.

4 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Find the line current from I=PVI = \frac{P}{V} at each voltage.

  2. Find the loss from P=I2RP = I^2R.

  3. Compare, and link the comparison to transformers.

Watch out for

  • Using P=V2RP = \frac{V^2}{R} with the transmission voltage. The 25 kV25\ \mathrm{kV} is not across the line resistance; most of it is across the load.

Why is electricity transmitted over long distances at very high voltage?

Choose one answer

Note

From power station to power point

In Queensland, generators produce electricity at tens of kilovolts. Step-up transformers raise it to as much as 275275 or 330 kV330\ \mathrm{kV} for the high-voltage transmission network. Substations then step it down for local distribution, for example to 11 kV11\ \mathrm{kV} along suburban streets, and a final pole-top or ground-level transformer supplies homes at 230 V230\ \mathrm{V}.

History

The first transformer

Faraday's iron ring of 1831, with two separate coils wound on it, was in effect the first transformer. Practical transformers in the 1880s made it possible to send alternating current over long distances, which is a big part of why the world's grids run on AC.

Summary

  • A transformer works by electromagnetic induction. The AC in the primary makes a changing flux in the core, which induces an EMF in the secondary (Faraday's law).

  • VpVs=NpNs\frac{V_p}{V_s} = \frac{N_p}{N_s}: more turns on the secondary steps the voltage up.

  • IpVp=IsVsI_pV_p = I_sV_s for an ideal transformer: when the voltage goes up, the current goes down.

  • Transformers need AC, because a steady flux induces nothing. Laminated cores reduce eddy-current losses.

  • Transmitting at high voltage means a small current, which keeps the I2RI^2R losses in the lines small.

Finished the lesson?

Try the 3 quick checks above and the lesson completes itself, or mark it complete now.

Lesson 11 of 120% read

Save your progress with a free account