Lesson 10 of 12 · 18 min

Moving conductors and AC generators

Describe how an EMF is induced across a conductor moving through a magnetic field, calculate it from the area it sweeps out, and explain how an AC generator produces an alternating EMF.

What you will be able to do

  • Describe the process that induces an EMF across a conductor moving through a magnetic field.
  • Calculate the EMF across a moving rod from Faraday's law, emf=BLv\text{emf} = BLv.
  • Explain how an AC generator produces an alternating EMF, and calculate its average EMF over part of a turn.
  • Describe how electricity is generated in power stations, including renewable sources.

Moving a magnet near a coil is one way to change flux. Another is to move the wire itself. Push a metal rod through a magnetic field and a potential difference appears between its ends. Spin a coil in a field and you have a generator.

Coal, gas, hydro and wind power stations all make electricity this way, as do the alternator in a car and a bicycle dynamo.

Why does a moving rod get an EMF? A metal rod is full of free electrons. Move the rod at velocity vv through a field BB and its electrons move with it, so each feels a magnetic force F=qvBF = qvB directed along the rod. Electrons pile up at one end, leaving the other end positive.

The separated charge sets up an electric field inside the rod that pushes back on the electrons. Charge stops building up when the electric force balances the magnetic force, leaving a steady potential difference between the ends: the induced EMF.

Field into the page, rod moving right. Positive charges would be pushed up the rod, so electrons are pushed down: the top end becomes positive and the bottom end negative.

How an EMF appears across a moving rod

  1. The rod carries its free electrons through the field

  2. Each electron feels a magnetic force along the rod

    F=qvBF = qvB, with its direction from the palm rule (reversed for electrons).

  3. Charge separates

    Electrons collect at one end; the other end is left positive.

  4. An opposing electric field builds up

    The separated charge makes an electric field in the rod that pushes electrons back.

  5. Equilibrium

    When the electric force balances the magnetic force, no more charge moves, and a steady EMF remains across the rod.

Deriving emf=BLv\text{emf} = BLv

Let the rod (length LL) slide along two rails so that it completes a circuit. In time Δt\Delta t it moves vΔtv\Delta t, adding an area ΔA=LvΔt\Delta A = Lv\Delta t to the loop. Faraday's law with N=1N = 1 gives

∣emf∣=BΔAΔt=BLvΔtΔt=BLv|\text{emf}| = \frac{B\Delta A}{\Delta t} = \frac{BLv\Delta t}{\Delta t} = BLv

The force picture gives the same result: the EMF is the work done per coulomb pushing charge along the rod, (qvB)Lq=BLv\frac{(qvB)L}{q} = BLv. This formula isn't in the formula book, so be ready to derive it from Faraday's law.

A ute drives at 15 m s−115\ \mathrm{m\,s^{-1}} with a horizontal steel bar 1.2 m1.2\ \mathrm{m} long on its roof rack, at right angles to its motion. The vertical component of Earth's magnetic field there is 5.0×10−5 T5.0 \times 10^{-5}\ \mathrm{T}. Calculate the EMF between the ends of the bar.

in V

Give 2 significant figures.

Worked example

Energy in a rod sliding on rails

  • Complex unfamiliar
  • Technology active

A metal rod 0.50 m0.50\ \mathrm{m} long slides at a constant 4.0 m s−14.0\ \mathrm{m\,s^{-1}} along two parallel rails joined at one end by a 2.0 Ω2.0\ \Omega resistor. A uniform 0.20 T0.20\ \mathrm{T} field points into the page, perpendicular to the plane of the rails.

(a) Calculate the EMF induced across the rod.

(b) Calculate the current.

(c) Calculate the force needed to keep the rod moving at constant speed, and show that the mechanical power supplied equals the electrical power.

5 steps

Try it yourself first, then check the working one step at a time.

Method

  1. EMF from the rate at which the loop's area (and so its flux) changes: emf=BLv\text{emf} = BLv.

  2. Current from V=IRV = IR, then the opposing force from F=BILF = BIL.

  3. Check energy conservation by comparing Fv with VI.

Watch out for

  • Thinking no force is needed at constant speed. Without a push, the magnetic force on the induced current slows the rod down.

Key idea

Lenz's law in a moving rod

When the induced current flows, the rod becomes a current-carrying wire in a field, so it feels a force F=BILF = BIL. By Lenz's law this force opposes the motion. To keep the rod moving you have to keep pushing, and the work you do is exactly the electrical energy produced. That is why a generator gets harder to turn the more current you draw from it.

Generators. An AC generator is a coil turning in a magnetic field. As it rotates, the angle between the field and the normal to the coil changes continuously, so the flux ϕ=BAcos⁡θ\phi = BA\cos\theta rises and falls, and the induced EMF keeps reversing. Slip rings and brushes connect the spinning coil to the outside circuit without the wires twisting up.

Interactive

An AC generator

Watch the flux and the EMF as the coil turns. Where is the coil when the EMF is largest? What happens when you add turns or strengthen the field?

Flux (dashed) and EMF (solid) for a generator coil. At A the plane of the coil is perpendicular to the field: flux maximum, EMF zero. At B, a quarter turn later, the plane is parallel to the field: flux zero but changing fastest, so the EMF is largest.

Key idea

Reading generator graphs

The EMF is −N-N times the gradient of the flux–time graph. When the flux is at a maximum or minimum its gradient is zero, so the EMF is zero. When the flux crosses zero it is changing fastest, so the EMF is largest.

Turning the coil twice as fast halves the period and doubles the rate of change of flux: the peak EMF and the frequency both double. More turns, a stronger field or a larger coil also raise the peak EMF.

In which position of a rotating generator coil is the induced EMF largest?

Choose one answer

Worked example

Average EMF of an AC generator

  • Complex familiar
  • Technology active

An AC generator has a coil of 100 turns, each of area 0.050 m20.050\ \mathrm{m^2}, rotating at 25 revolutions per second in a uniform 0.20 T0.20\ \mathrm{T} field. Calculate the average EMF induced during the quarter turn from where the plane of the coil is perpendicular to the field to where it is parallel to the field.

4 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Find the flux at the start and end positions.

  2. Find the time taken from the rotation rate.

  3. Use ∣emf∣=NΔϕΔt|\text{emf}| = N\frac{\Delta\phi}{\Delta t} for the average.

Watch out for

  • Using the time for a whole revolution, over which the average EMF is zero.

Note

Investigate: the AC generator

Connect a hand-cranked generator, or a small motor used in reverse, to a data logger or oscilloscope. The trace is a sine wave. Turn the handle faster and the peaks get taller and closer together. A graph of peak EMF against rotation rate is a straight line through the origin, as Faraday's law predicts.

Note

How electricity is made

Coal, gas, nuclear, hydro and wind power stations all spin generators: steam, water or wind turns a turbine, and the turbine turns a magnet inside fixed coils (large generators spin an electromagnet, which avoids carrying huge currents through sliding contacts). Renewable sources use the same physics with a different push: wind turbines, hydro-electric and pumped-hydro schemes, and solar-thermal plants that make steam with sunlight.

Solar photovoltaic panels are the exception. They turn light directly into electricity with no moving parts and no induction, producing DC that an inverter converts to AC for the grid.

A generator is turned at twice its original rate. What happens to the peak EMF and the frequency of its output?

Choose one answer

Common mistake

Average, peak and the quarter turn

  • Over a whole revolution the flux returns to its starting value, so the average EMF is zero. Average-EMF questions use a quarter or half turn.
  • The EMF is largest when the flux is zero, not when it is largest.
  • In the rod formula, LL is the length of the rod and vv its speed, both perpendicular to the field.

Summary

  • A conductor moving through a magnetic field has an EMF induced across it. The magnetic force on its free charges separates them until an electric field balances it.

  • A rod of length LL moving at vv perpendicular to BB sweeps area at rate LvLv, so emf=BLv\text{emf} = BLv (from Faraday's law).

  • The force on the induced current opposes the motion (Lenz's law), so work must be done to keep it moving. That work becomes electrical energy.

  • In an AC generator the flux through a rotating coil changes continuously, so the EMF alternates. It is largest when the plane of the coil is parallel to the field.

  • Faster rotation raises both the peak EMF and the frequency. The average EMF over a quarter turn is NBAT/4N\frac{BA}{T/4}.

Finished the lesson?

Try the 3 quick checks above and the lesson completes itself, or mark it complete now.

Lesson 10 of 120% read

Save your progress with a free account