Lesson 6 of 12 · 17 min

Force on a current-carrying wire

Describe and calculate the force on a current-carrying wire in a magnetic field with F=BILsin⁡θF = BIL\sin\theta and the right-hand palm rule, interpret current-balance data and explain how a DC motor turns.

What you will be able to do

  • Describe the force on a current-carrying conductor in a magnetic field.
  • Calculate the force with F=BILsin⁡θF = BIL\sin\theta and find its direction with the right-hand palm rule.
  • Interpret data from a current-balance experiment to find a magnetic field.
  • Explain how the forces on a coil make a DC motor turn.

A wire carrying a current through a magnetic field gets pushed sideways. That push turns every electric motor, from the fan in a laptop to the motors driving an electric car's wheels.

It happens because a current is moving charge, and moving charges in a magnetic field feel a force. Add up the forces on all the charges in the wire and you get the force on the wire.

Interactive

The motor effect

Reverse the current, then reverse the field. What happens to the force each time? Turn the wire until it is parallel to the field.

Key idea

Force on a current-carrying wire

A wire carrying current II in a magnetic field BB experiences a force

F=BILsin⁡θF = BIL\sin\theta

where LL is the length of wire in the field and θ\theta is the angle between the wire (the current) and the field. The force is largest when the wire is perpendicular to the field and zero when it is parallel. It is always perpendicular to both the wire and the field.

Key idea

The right-hand palm rule

Hold your right hand flat. Point your fingers along the magnetic field (from N to S) and your thumb along the conventional current. Your palm faces the direction of the force, as if you were pushing with it.

Field into the page, current to the right: fingers into the page, thumb to the right, and your palm pushes up the page.

A 12 cm12\ \mathrm{cm} length of wire carries 2.5 A2.5\ \mathrm{A} at right angles to a 0.40 T0.40\ \mathrm{T} magnetic field. Calculate the force on it.

in N

Give 2 significant figures.

A wire carries a current to the right, across the page, through a magnetic field that points up the page. What is the direction of the force on the wire?

Choose one answer

Worked example

Size and direction of the force on a wire

  • Simple familiar
  • Technology active

A 25 cm25\ \mathrm{cm} length of wire carrying 4.0 A4.0\ \mathrm{A} lies in a uniform 0.60 T0.60\ \mathrm{T} magnetic field.

(a) Calculate the force on it when it is perpendicular to the field.

(b) Calculate the force when the wire makes 30∘30^\circ with the field.

(c) In part (a) the field points into the page and the current flows to the right. Find the direction of the force.

3 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Use F=BILsin⁡θF = BIL\sin\theta with θ\theta between the wire and the field.

  2. Right-hand palm rule: fingers along BB, thumb along II, palm pushes in the direction of FF.

Watch out for

  • Using cos⁡θ\cos\theta: the force is largest at 90∘90^\circ and zero when the wire is parallel to the field.

Common mistake

Angles and currents

  • θ\theta is the angle between the wire and the field. A wire parallel to the field feels no force at all.
  • The palm rule uses conventional current. If a question describes electron flow, the conventional current is the other way.
  • LL is only the length of wire actually inside the field.

Investigate: the current balance. A U-shaped magnet sits on an electronic balance, and a stiff horizontal wire, clamped in place, runs between its poles. Switch on a current and the balance reading changes. The field pushes the wire one way and, by Newton's third law, the wire pushes the magnet the other way with an equal force.

The change in reading converts to a force with F=Δm gF = \Delta m\,g (with Δm\Delta m in kilograms). Vary the current and the force should be proportional to it; vary the length of wire in the field and the force should be proportional to that too.

Worked example

Finding B from current-balance data

  • Complex familiar
  • Technology active

In a current-balance experiment, a horizontal wire is clamped between the poles of a U-shaped magnet that sits on an electronic balance. 5.0 cm5.0\ \mathrm{cm} of the wire is in the field, perpendicular to it. The table shows the change in the balance reading, Δm\Delta m, for different currents. Use the data to determine the magnetic field strength between the poles.

II (A)01.02.03.04.05.0
Δm\Delta m (g)0.000.440.861.311.722.18
4 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Turn the balance reading into a force with F = Δm g.

  2. Plot the quantity that should be proportional (Δm\Delta m or FF against II) and draw a line of best fit.

  3. Relate the gradient to the formula: here gradient =BLg= \frac{BL}{g}.

Watch out for

  • Forgetting to convert grams to kilograms before multiplying by g.

  • Using one data point instead of the gradient of the best-fit line.

In a current-balance experiment a student plots force against current. The graph is a straight line through the origin with gradient 4.0×10−3 N A−14.0 \times 10^{-3}\ \mathrm{N\,A^{-1}}. The length of wire in the field is 5.0 cm5.0\ \mathrm{cm}. What is the magnetic field strength?

Choose one answer

Motors. In a DC motor a coil of wire sits between the poles of a magnet. The current flows one way along one side of the coil and back the other way along the opposite side, so the two sides are pushed in opposite directions and the coil turns. Each side of an NN-turn coil feels a force F=NBILF = NBIL.

A split-ring commutator reverses the current in the coil every half turn, just as the coil passes the position where its plane is perpendicular to the field. Without it, the forces would push the coil back the other way and it would just rock. Carbon brushes press on the commutator to keep the current flowing as it spins.

Interactive

A DC motor

Watch the forces on the two sides of the coil. Which way do they point just after the commutator switches the current?

Two long parallel wires carry currents in the same direction. What happens to the wires?

Choose one answer

Exam tip

Explain your direction

In "determine the direction" questions, name the rule and the directions you used: "Using the right-hand palm rule, with fingers into the page (B) and thumb to the right (I), the force is up the page." A bare answer with no reasoning can lose the mark if it's wrong, and it doesn't show the marker your method.

Summary

  • A current-carrying wire in a magnetic field feels F=BILsin⁡θF = BIL\sin\theta, largest when the wire is perpendicular to the field and zero when parallel.

  • Right-hand palm rule: fingers along BB, thumb along the conventional current II, palm pushes in the direction of FF.

  • In a current balance, F=Δm gF = \Delta m\,g, and a graph of FF against II has gradient BLBL.

  • In a DC motor, opposite forces on the two sides of the coil turn it, and a split-ring commutator reverses the current every half turn.

  • Parallel wires attract when their currents are in the same direction and repel when they are opposite.

Finished the lesson?

Try the 4 quick checks above and the lesson completes itself, or mark it complete now.

Lesson 6 of 120% read

Save your progress with a free account