Lesson 8 of 8 · 22 min

Motion and modelling with definite integrals

Use definite integrals to find change in displacement, position and distance travelled from velocity, then set up, solve and evaluate definite integral models in context.

What you will be able to do

  • Find the change in displacement as ∫t1t2v(t) dt\int_{t_1}^{t_2} v(t)\,dt, and the position as x(t1)+∫t1t2v(t) dtx(t_1) + \int_{t_1}^{t_2} v(t)\,dt.
  • Find the distance travelled by splitting where v(t)=0v(t) = 0, which is ∫t1t2∣v(t)∣ dt\int_{t_1}^{t_2} |v(t)|\,dt.
  • Model a situation with a definite integral, solve it with or without technology, and judge whether the answer is reasonable.

Velocity is the rate of change of displacement, so by the last lesson, integrating velocity gives the change in displacement. On a velocity–time graph that is the signed area. A particle that goes forwards 3 m and back 2 m has changed its displacement by 1 m, but it has travelled 5 m. Distance counts every metre, whichever way the particle moves.

Interactive

Displacement and distance

Here v(t)=t2−4t+3=(t−1)(t−3)v(t) = t^2 - 4t + 3 = (t - 1)(t - 3). Scrub through time: the particle moves right until t=1t = 1, left until t=3t = 3, then right again. Compare the displacement at t=4t = 4 with the distance it has travelled.

Blue areas are motion in the positive direction; the red area is motion back the other way.

Key idea

Three different questions

For a particle with velocity v(t)v(t) on t1≤t≤t2t_1 \le t \le t_2:

  • Change in displacement =∫t1t2v(t) dt= \int_{t_1}^{t_2} v(t)\,dt (signed area).
  • Position at t2t_2 =x(t1)+∫t1t2v(t) dt= x(t_1) + \int_{t_1}^{t_2} v(t)\,dt.
  • Distance travelled =∫t1t2∣v(t)∣ dt= \int_{t_1}^{t_2} |v(t)|\,dt. By hand, find where v(t)=0v(t) = 0, split there, and add the sizes of the pieces.

Worked example

Displacement and distance from velocity

  • Complex familiar
  • Technology free

A particle moves in a straight line with velocity v(t)=t2−4t+3 m s−1v(t) = t^2 - 4t + 3\ \mathrm{m\,s^{-1}} for 0≤t≤40 \le t \le 4.

(a) Find the change in displacement over the 4 seconds.

(b) Find the distance travelled in the 4 seconds.

5 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Displacement: integrate vv over the whole interval.

  2. Distance: find where v=0v = 0, integrate each piece, add the sizes.

Watch out for

  • Giving 43\frac{4}{3} m as the distance.

  • Missing one of the two turning times.

A particle moves in a straight line with velocity v(t)=2t−6 m s−1v(t) = 2t - 6\ \mathrm{m\,s^{-1}}. Find the change in its displacement over the first 5 seconds.

in m

For the same particle, v(t)=2t−6v(t) = 2t - 6, find the distance travelled over the first 5 seconds.

in m

A particle starts at x=2x = 2 m and moves with velocity v(t)=3t2 m s−1v(t) = 3t^2\ \mathrm{m\,s^{-1}}. Use a definite integral to find its position at t=2t = 2 s.

in m

Common mistake

Displacement is not distance

∫v(t) dt\int v(t)\,dt and ∫∣v(t)∣ dt\int |v(t)|\,dt are equal only if the particle never changes direction. Always check for times inside the interval when v(t)=0v(t) = 0. With technology, integrate ∣v(t)∣|v(t)| directly for the distance.

Modelling with a definite integral

  1. Define the variables

    Say what tt and the rate measure, with units, and the interval the model covers.

  2. Decide what the integral represents

    A change, a final amount (add the start), an area, or a distance.

  3. Set up and evaluate

    Write the integral with its terminals. Evaluate exactly, or with technology.

  4. Interpret

    Answer the question in a sentence with units.

  5. Check reasonableness

    Is the size and sign sensible? Does the model hold over the whole interval, or does it break down (a negative volume, a time outside the domain)?

Worked example

Filling and draining a tank

  • Complex unfamiliar

A rainwater tank holds 500 L at 1 pm. For the next 40 minutes, rain runs in at a steady 30 L per minute while a pump draws water out at 2t2t L per minute, where tt is the time in minutes after 1 pm.

(a) Write an expression for the volume V(T)V(T) in the tank at time TT, as a definite integral, and simplify it.

(b) Find the maximum volume in the tank and when it occurs.

(c) The tank manager says the pump will empty the tank before 1:40 pm. Evaluate this claim.

6 steps

Try it yourself first, then check the working one step at a time.

Method

  1. Net rate == rate in −- rate out.

  2. Amount == starting amount +∫+ \int net rate.

  3. The maximum occurs where the net rate changes sign.

  4. Test claims against the model and its domain.

Watch out for

  • Forgetting the starting 500 L.

  • Treating the time of maximum volume as when the outflow is greatest.

Exam tip

Read the motion words

"Displacement" or "change in position" wants ∫v dt\int v\,dt. "Position" or "where is it" wants the starting position added. "Distance travelled" or "how far has it gone" wants ∫∣v∣ dt\int |v|\,dt. "Initially" means t=0t = 0, and "during the third second" means 2≤t≤32 \le t \le 3.

Summary

  • Change in displacement =∫t1t2v(t) dt= \int_{t_1}^{t_2} v(t)\,dt, the signed area under the velocity graph.

  • Position == starting position ++ change in displacement.

  • Distance travelled =∫t1t2∣v(t)∣ dt= \int_{t_1}^{t_2} |v(t)|\,dt: split where v(t)=0v(t) = 0 and add the sizes.

  • In a model, say what the integral represents, evaluate it, answer in context with units, and check reasonableness.

  • Check the model holds over the whole interval before trusting the answer.

Finished the lesson?

Try the 3 quick checks above and the lesson completes itself, or mark it complete now.

Lesson 8 of 80% read

Save your progress with a free account