Lesson 5 of 8 · 18 min
Area between curves
Find the area between two curves by integrating the upper curve minus the lower curve between their points of intersection, splitting wherever they cross, with and without technology.
What you will be able to do
- Find the points of intersection of two curves to get the terminals.
- Calculate the area between curves as , where .
- Split the region where the curves cross, so the upper curve is always on top.
- Use technology to find intersections and areas between curves.
The area between two curves is the area under the top one minus the area under the bottom one. Think of a thin vertical strip: its height is the gap between the curves, top minus bottom, and the area is the sum of all those strips. That is why it works even when part of the region is below the -axis. Sliding both curves up by the same amount does not change the gap.
Each strip runs from the line up to the parabola , so its height is . Increase and the strips fill the region, closing in on the exact area .
Key idea
Area between two curves
If for every in , the area between and from to is
Upper curve minus lower curve. If no terminals are given, the region is enclosed by the curves and the terminals are the -coordinates of the points of intersection. This rule is not on the formula sheet.
Worked example
Area enclosed by and
Find the area of the region enclosed by the parabola and the line .
Step 1: Find the points of intersection
, so or .
Step 2: Decide which curve is on top
At : the parabola gives and the line gives , so the parabola is on top on .
The curves only swap at an intersection, so one test value decides the whole interval.
Step 3: Set up upper minus lower
Step 4: Integrate
Step 5: Simplify
Try it yourself first, then check the working one step at a time.
Answer
The enclosed area is square units.
Method
Solve the equations simultaneously for the terminals.
Test a value between them to find the upper curve.
Integrate upper minus lower, simplified first.
Watch out for
Losing a sign when subtracting : it is .
Getting wrong inside : at it is .
Find the area of the region enclosed by and .
Curves can swap places. Between and , starts on top, the curves cross at , and then is on top. A single integral of across the whole interval would let the two pieces cancel.
Between and the upper curve changes at , so the area comes in two pieces.
Find the exact area between and for .
Common mistake
Two ways to lose the area
Lower minus upper gives a negative answer. Missing a crossing lets pieces cancel. Before integrating, check which curve is on top by testing a value of in each interval, and look for intersections inside the interval.
Worked example
Area between and , with technology
The curves and enclose a region. Use technology to find its area, correct to 3 decimal places.
Step 1: Find the intersections
has no algebraic solution. Graph both and use the intersect tool: and . Store them as and without rounding.
Rounding the terminals early can change the third decimal place of the area.
Step 2: Decide which curve is on top
At : and , so the line is on top.
Step 3: Set up the integral
Step 4: Evaluate with technology
The integral tool gives
Step 5: Check reasonableness
The region is about 3 units wide and at most about 1.2 units tall, so an area near 2 is sensible.
Try it yourself first, then check the working one step at a time.
Answer
The area is approximately square units.
Method
Find intersections with the intersect tool and store them.
Test a point to find the upper curve.
Write the integral, then evaluate it with technology.
Watch out for
Typing the integrand as , which gives .
Rounding the terminals to 1 decimal place before integrating.
Without technology
Solve algebraically for the intersections, decide which curve is on top, then integrate exactly with the fundamental theorem.
With technology
Graph both curves and use the intersect tool. Store the -values rather than rounding them, then evaluate , or if the curves swap places. Write the integral you evaluated and the intersections you used.
Exam tip
Write the set-up
Most of the marks are for the set-up: the intersections, a statement of which curve is on top, and the integral of upper minus lower with the right terminals. Shade the region on a sketch, and state the area in square units.
Summary
Area between curves .
The terminals of an enclosed region are the -coordinates of the points of intersection.
Test a value to decide which curve is on top.
If the curves cross inside the interval, split there and integrate each piece with the right curve on top.
The rule works even below the -axis: only the gap between the curves matters.
Finished the lesson?
Try the 2 quick checks above and the lesson completes itself, or mark it complete now.